Yocto thermocouple jobber

...user space. Work with Linux-based embedded systems, including Petalinux and Yocto Project. Collaborate with hardware engineers to ensure proper integration between hardware and software. Debug and test embedded systems to ensure performance and reliability. Document software architecture, design, and testing procedures. Qualifications: Bachelor's degree in Electrical Engineering, Computer Science, or a related field. Proven experience in embedded software development. Proficiency in C/C++ programming for embedded systems. Strong knowledge of Linux-based embedded systems, including configuration and build processes. Experience with custom driver development in kernel and user space. Familiarity with Petalinux and Yocto Project. Hands-on experience with Xilinx Zynq de...

I'm seeking a skilled professional to design a PCB and firmware for a multichannel thermocouple registrator. Assumptions 1. PCB as small as possible, housing on our side 2. internal flash - approx. 4/8/16gb or other - please advise 3. buttons 3.1 START (recording) 3.2 STOP (recording stop) 3.2 LED light (indicating recording) 3.4 LED light (indicating low battery) 3.5 LED light (indicating full disk/writing error) 3.6 ON/OFF (main button) 4. replaceable battery, preferably a finger or similar - we can make a housing for it 5. 8 channels for thermocouples 6. USB C for reading data (mass disk) 7. 4 screw holes for mounting in the housing 8. buttons and LEDs on Front panel 9. Thermocouple K sockets from top side Functionality 1. START button creates a new *.csv file, with...

...evices

I'm seeking an experienced PCB designer with expertise in Altium to create a complete design for an ultra-small 34x30mm board. This board is intended for use as an Internet of Things (IoT) device, so the design must prioritize compactness without sacrificing functionality. Key Requirements: - Imx 8m nano ultralight 11x11 - display oled small - cam small 16pin custom ffc or other solution because 24 pins is to much for fit inside shape - The board should support Wi-Fi and Bluetooth for wireless communication. - Connectivity must be limited to USB pads, with the design exclusively accommodating BGA chips. - lpddr4x + emmc epop kingston Ideal candidates should have a strong background in designing small form-factor IoT devices and be proficient with Altium. Previous experience working ...

- The environment of yocto is ready configure on Ubuntu

- The environment of yocto is ready configure on Ubuntu

I'm looking for an experienced penetration tester to perform structured penetration testing of a Linux (Yocto distribution). This penetration testing will occur within a lager security risk management evolution. The PenTesting needs to be both performed and documented in a manner acceptable within the AAMI SW96 and IEC 81001-5 criteria. The testing will cover multiple components of the system. [HARD REQUIREMENT: We require a hybrid of on-site and remote work --- YOU AND YOUR LAB MUST BE LOCATED WITHIN THE GREATER MINNEAPOLIS/ METRO AREA. Key Areas of Focus will be coverage of the enumerated vulnerabilities applicable to this custom developed Yocto Linux device, and will include applicable aspects of: - Network services - File system integrity - User and group perm...

We have a controller for our system that uses two processor modules (CM4 and STM32/Nucleo Board) and has onboard DC/DC modules, BLDC Motor Drivers and FETs, Stepper Motor Drivers and FETs, Digital I/O to communicate with sensors and actuators, and K-Type Thermocouple sensors. We are looking for a very experienced EE that is an expert in achieving FCC Class B. We have a current design which is very close to getting Class A, but getting to Class B will require a board respin. The system is a highly automated countertop appliance in the food services industry.

I am currently working on building a Yocto OS for a Single Board Computer (SBC), specifically the Phytec i.MX8MP. The build has been configured with only the essential layers. However, I am encountering three remaining dependency errors related to application layers that I need assistance with to complete the build successfully. I am looking for someone with: - Experience with the Yocto Project and Linux embedded systems. - Familiarity with the Phytec SBC. - Ability to troubleshoot and resolve build errors in Yocto. - Strong communication skills for an interactive session to address the issues. The tasks will include: - Reviewing the current Yocto build configuration and identifying the source of the last three errors. - Providing guidance and support in real...

I need a circuit designed that can control a 180-degree servo based on temperature readings from a thermocouple. The servo will be located inside a smoker and needs to operate between 200 degrees and 250 degrees. This circuit will be powered by an AC adapter. Ideal Skills and Experience: - Proficiency in circuit design - Experience with temperature-controlled servo systems - Familiarity with using thermocouples - Knowledge of AC-powered circuits - Ability to design for high-temperature environments

using basics components like : OPAMPs: LM358 (contains two OPAMPs), TL062 (two OPAMPs, FET input), TL084 (four OPAMPs, FET input), LM324 (four OPAMPs); zener diodes; BJTs: BC238, 2N3904, BC308, BD135, BD136, JFET: BF245 (with njf symbol in LTSpice, n-Channel, VT=−2.3V), MOSFET: 2N7000 (with nmos symbol, n-channel, VT=1.6V), red LED, standard resis...like : OPAMPs: LM358 (contains two OPAMPs), TL062 (two OPAMPs, FET input), TL084 (four OPAMPs, FET input), LM324 (four OPAMPs); zener diodes; BJTs: BC238, 2N3904, BC308, BD135, BD136, JFET: BF245 (with njf symbol in LTSpice, n-Channel, VT=−2.3V), MOSFET: 2N7000 (with nmos symbol, n-channel, VT=1.6V), red LED, standard resistors, standard capacitors, K-type thermocouple, 2-pin PCB connector, 10K trimpot. I need a heater contro...

We are looking for software level product training on our Linux based embedded PC product. Result required: When an embedded PC is shipped to a product development engineer (customer) , he must be able to answer all technical questions and assist the development engineer(customer) on software level while he is developing his that, we need complete training on embedded linux and yocto project fundamentals relevant to linux based PCs. There are 4-5 manuals associated with the product and we also require training on the same. We are attaching herewith reference documents of our product. (Kindly refer the flyer and software manual) For any further information you may refer :

Vennligst Registrer deg eller Logg inn for å se detaljer.

Project - Linux Dev I am looking to work with a developer familiar with Linux implementations. This will be a long term project with a deadline of end of 2024. We are currently developin...have already existing (replacing an old Legacy PLC/HMI design). For this project we want to work with someone initially on a Consulting basis where we will chat frequently about the best design practices and ask for advice/collaboration. In the near future, once we have a successful test setup, we will want this team to help us build a custom image configuration (either based on Raspbian or Yocto) that we can deploy on our equipment. We are using off-the-shelf items for development. We may use this in production as it has a lot of what we need already. Hardware: - Seeed Studio reTermin...

I need someone to write c++ code for an arduino R4 wifi. The device needs to connect to wifi and receive temperature data from a max 6675 k type thermocouple. The temperature then needs to be transmitted to thingsboard once every 30 seconds.

I'm looking for an experienced PCB designer who can help create a pcb to collect temperature data from a k type thermocouple and transmit it to thingsboard. The pcb should have both Wifi and GSM(Australia) compatibility, and as such two sets of code which can be uploaded as needed depending on whether we are using GSM of Wifi. The device should send the temperature, a device ID and Date/time to Thingsboard every 10 seconds. The PCB should be ready for printing/production with code working and ready for upload.

I'm looking for a skilled Hardware/Embedded Engineer with hands-on experience with the Yocto Project and expertise in working with the NanoPi platform. The primary objective of this project is to develop new features for our current setup. Ideal Skills: - Extensive knowledge and experience with NanoPi - Proficiency in Yocto Project - Strong hardware and embedded systems skills - Software development skills related to embedded systems - Experience in developing new features on hardware platforms Experience: - Prior involvement in similar projects - Proven track record in hardware/embedded engineering - Demonstrated ability to develop new features on hardware platforms. - Preferably from Gurugram

I'm seeking a professional to help develop an IoT device based on STM32. This device should be capable of connecting through 5G and performing data collection. Key Features: - The IoT device must be equipped with the following sensors: - Temperature sensor - Humidity sensor - Motion sensor - WIFI - Bluetooth Other IOT features needed: 1. Full detailed GPS tracking 2. Thermocouple connectivity with Internal and external temperature 3. Tilt 4. Humidly 6. Battery Level should last 20 days minimum. 7 Pressure Hardware should be cheap and Firmware code should be ready to work with. The firmware programming shall be flexible to make future config and enhancements. The hardware should be modifiable for future changes. - The primary function of the device should ...

...Linux system. The system is based on Yocto and designed for an ARM processor (specifically, the NXP ). Your responsibilities will primarily include: - **Feature Development**: The main focus of this project is to extend the system with new features. - **Documentation**: Thoroughly documenting your work is essential. You should be able to provide clear, concise and comprehensive documentation. - **Testing**: You will also be expected to test the system after any modifications or additions are made. The ideal candidate should have strong experience with: - Embedded Linux systems - Yocto Project - ARM processors - Linux system testing - Documenting technical information - Providing detailed project proposals - At least intermediate experience with the Yocto Project...

I'm urgently needing a highly skilled Yocto developer who can immediately take on the following tasks: - Software Configuration: Setting up the build environment is the primary task, also including configuring both the kernel and various packages. Demonstrable previous experience with this scope of software configuration is highly desirable. - Custom Package Development: The second task requires development of unique packages. The exact specifications will be provided once the project begins. Time is of the essence here, so I'm looking for someone with excellent problem-solving skills and a proven track record in delivering efficient results in a demanding timeframe. Prior experience working with Yocto Project is a must-have.

I'm seeking an expert in utilizing Arduino Mega 2560 WiFi Board, K Type thermocouple with MAX6675 amplifier and MPU 6050 sensor. The primary function of the project is to measure and display temperature accurately and activate a coil via relay to maintain a desired temperature. Additional requirements include: - Capable of stabilizing mechanical parts within a rectangular frame. - Use the high temperature readings to activate four servo motors that level the rectangular frame. - Proficiency in hardware interfacing, particularly with sensor systems and Arduino, is highly desirable for this project. Ideal skills include: - Strong understanding of Arduino programming and functions. - Experience with sensor systems, specifically temperature and level sensors. - Knowledgeable in u...

I'm seeking a professional with expert knowledge in precision analog design. Goal of the project is a small prototype board to measure K type thermocouple elements - with two different approaches. Additionaly obvisouly a MCU will take place - as well as RS485 communication. Absolut main aspect is an accurate (in sense of stability, low noise and absolute value representation) K thermocouple element measurement. Two approaches are forseen - using the high precision MAX31856 as well as the AD8495 in conjunction with a 20-bit SAR and 24-bit SigDelt ADC. Apart from the ADC proposition the project comprisis of a full circuit and PCB creation. Additionaly also the needed firmware for the respective communication (over SPI) shall be properly implemented (well structured and ...

... KEY TASKS: * Development of device drivers to establish a seamless communication between the Embedded Linux Operating System on IMX6 board and our USB devices - USB Camera and USB printer. * Thorough testing of the device drivers to ensure compatibility with Linux and smooth functioning of the hardware. Linux OS is already installed on board IDEAL SKILLS: * Required changes to Linux OS with Yocto project * Proficiency in the Linux operating system is crucial. * Demonstrated expertise in driver development specifically regarding USB devices such as cameras and printers. * Comprehensive understanding of USB Camera and USB printer is advantageous. * Strong knowledge of debugging is beneficial, to iron out any potential issues during driver development. If your expertise aligns...

I'm looking for a skilled Yocto Linux Developer to work on a project involving IoT devices specifically designed for telemetry. Key Responsibilities: - Customize the Linux kernel to fit our project's specific requirements - Build and configure Yocto images for smooth operation - Integrating and testing hardware components to ensure maximum functionality Ideal Candidate: The successful applicant should have significant experience in embedded Linux development, specifically with Yocto. Proficiency in kernel customization, building and configuring Yocto images, and hardware integration/testing is required. Familiarity with IoT devices, particularly in telemetry, would be a significant advantage. With your expertise, we will develop a reliable, tailo...

I am in need of a skilled embedded software engineer able to create a customized Yocto Linux Build specifically for my Variscite MX93 V2-A SOM module. The build must include these specific features: - WiFi support - Bluetooth support - Custom device drivers - CAN x2 support Build Instructions and Resources can be found at I also need the build to be based on a specific kernel version (Kernel V6.1.36). Ideal candidates should have experience in Linux operating systems, with specific knowledge of Yocto Linux being a major advantage. Experience in custom software builds and creating device specific drivers would certainly make you standout. Effective communication is critical for this project, as I look forward to regularly reviewing your progress

...inverter modules (half bridge) at different power and switching frequencies and monitor key parameters during testing. I would also like to measure temperature on the top of the device (with the top cover open) via an IR camera. - Required measurements/ key parameters: Input variables such as voltage, current, switching frequencies, and any other parameters Temperature via the IR camera and a thermocouple in the coolant line Coolant flow rate I currently lack clarity on the equipment and setup required for such testing. Recommendations or guidance on necessary items, such as testing kit, power supply, any other equipment will be greatly appreciated. I can provide the cooling loop and the IR camera if it needs to be setup at our facility. Ideal candidates will have detailed ...

I'm seeking skilled freelancers to bring up the iMax6 SOC Linux and develop a test application. This task will include: 1. Linux Deployment: You'll need to deploy Debian on the iMax6 SOC. Experience with SOC Linux configurations, especially with Debian, is crucial. Yocto also OK 2. Test Application Development: You'll develop an application allowing for: - I2C Communication - SPI Communication - GPIO Control - CAN Communication Prior knowledge in these specific types of communication and control is required. Note: The end-users for this project haven't been determined yet. However, a user-friendly and intuitive design could be beneficial for possible end consumers or system administrators besides developers.

Project Description: I am looking for a skilled developer to integrate a 10.1 inch capacitive lvds/rgb touchscreen on a Raspberry Pi ARM board running a custom Yocto built Linux. The ideal candidate should have experience with the following: - Capacitive touchscreen integration - Raspberry Pi development - Linux customization and development with Yocto The project will involve: - Configuring the Raspberry Pi to recognize and interact with the capacitive touchscreen - Customizing the Yocto built Linux to support the touchscreen functionality - Testing and debugging the integration to ensure smooth operation - Touchscreen calibration feature needed If you have the necessary skills and experience, please submit your proposal outlining your relevant experience and appr...

I am looking for a freelancer who can design and build an 8 channel J type thermocouple module. The module should be accurate Ideal Skills and Experience: - Experience in designing and building thermocouple modules. - Knowledge of J type thermocouples and their temperature ranges. - Ability to design a module with multiple channels. If you have the skills and experience required for this project, please submit your proposal.

...powering the device for up to 20 days. I'm looking for a freelancer who can help me create this device as soon as possible(in 2 -3 weeks may be). If you are experienced and have the skills to meet my specifications, please apply for this job. This should securely connect AWS IOT core MQTT broker. Need hardware, firmware and secure connect. IOT features needed: 1. Full detailed GPS tracking 2. Thermocouple connectivity with Internal and external temperature 3. Tilt 4. Humidly 6. Battery Level should last 20 days minimum. 7 Pressure 8. Size should be like cellphone size including battery. 9. Device should have certificate and securely bootstrap it. 10. During GPS location it needs to be accurate to the feet. Hardware should be cheap and be approximately $25. If more neede...

...skilled and experienced developer to help me with a Yocto project. I need to port the kernel from version 4.9-1.0.x-imx to version 4.17. . The two links below summarize what I want: The first contains the project link, to run it on your machine you will have to change the device to imx7d-pico and the machine command looks like this: MACHINE=imx7d-pico DISTRO=poky source setup-environment build and bitbake ipc-core-image-minimal And the second link is where the kernel that must be ported to the project above is located. The project will change from kernel 4.17 to 4.9-1.0.x-imx Note: The build has only worked on Ubuntu 18.04. You will probably need wsl2 or any machine with Ubuntu 18.04. first link: second

I am looking for a skilled developer with experience in Yocto to modify and compile at91bootstrap and u-boot bootloaders and kernel source. The specific modifications needed include: - Change RGB LED settings in order to modify the color boot sequence - Adding custom drivers - Implementing security patches The ideal candidate should have: - Strong knowledge and experience with Yocto - Proficiency in modifying and compiling bootloader and kernel source code - Familiarity with adding custom drivers and implementing security patches The project has a preferred timeline of completing within 1 week. However, if you have a flexible schedule and can meet the requirements within a different timeframe, please let us know.

I need a code from Github modified and fixed so it can be compiled and uploaded. This is the github project: Curre...multiple of ESP32 will be on the same network and I don't want name conflict. 3. I want all the updates source files so I can compile it further on my PC. Thank you ESP32 Board used: https://www.amazon.co.jp/gp/product/B08PB3SBQX/ref=ppx_yo_dt_b_asin_title_o03_s01?ie=UTF8&psc=1 Breakout Board Used: https://www.amazon.co.jp/gp/product/B092H9FM3R/ref=ppx_yo_dt_b_asin_title_o03_s01?ie=UTF8&psc=1 Thermocouple controller: https://www.amazon.co.jp/gp/product/B092ZCSM7J/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 Solid State Relay: https://www.amazon.co.jp/gp/product/B087JVVH51/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

Title: Yocto: Switch from sysVinit to systemd Overview: I am looking for a skilled freelancer who can assist me in switching the operating system from sysVinit to systemd in my yocto / poky project. I am not sure about the specific requirements for this switch and would appreciate some guidance. The project needs to be completed within 2 weeks. Requirements: - Expertise in yocto / poky development - In-depth knowledge of both sysVinit and systemd - Experience with system configuration and initialization processes - Strong understanding of Linux operating systems, specifically Ubuntu, CentOS, and Debian - Familiarity with yocto project structure and build processes Deliverables: - Detailed documentation outlining the steps required to switch from sysVinit to s...

1. Check remote access connection, to test environment for building and debugging to be sure that all process will go smoothly (1-2 hours) 2. Applying of RT patches to the kernel, build image for testing (3-5 hours) 3. Image test and debug (1-4 hours), it depends if there are some changes which should be implemented specific to the rockchip kernel 4. Custom layer recipe development (1-2 hours)

I am seeking a skilled developer to work on a Yocto Project that incorporates the RT-Preempt patch for Rock Pi E hardware by Radxa. You will be provided with SSH access to a system featuring: +Debian-based Linux +Cross-compiling tools already set up for Rock Pi +A functional Yocto2 environment configured for Rock Pi E +A working Yocto2 console image for Rock Pi E Requirements: +Experience with the Yocto Project and real-time preemptive kernels (RT-Preempt) +understanding of Rock Pi E hardware would be fine +Expertise in system optimization techniques for realtime os +Familiarity with Linux kernel development and customization +Your Responsibilities: Integrate the RT-Preempt kernel patch into the Yocto system Include all necessary components to compile and run the ...

Need RDK DAC build Downloadable Application Containers (DAC) is a RDK initiative to develop an experience Yocto image experience poky and dunfell experience Create a simple DAC app installation process for Raspberry Pi

...external (20K) ten turns potentiometer. The duty cycle: (0-100 %), needs to be adjustable via an internal or external (50K) ten turns potentiometer. Also needed is some code written for a feedback loop via a current sensor on the tank section of the induction heater for safety reasons. It's important that we also have code for a digital PID temperature controller that we have it has a type-K thermocouple input and it needs to be connected to the PWM outputs in some way for good temperature control. Lastly, the STM32H735G-DK evaluation kit needs to have several live data screens of GUI programming included in the programming to assist the user with getting to the functions and for monitoring the PWM squarewave signals and amplitude in real-time with several graphics pages...

Linux embedded SW developer, iMX6/Zynq we are looking for a skilled Linux embedded software developer to work on a project involving the iMX6 hardware platform (Variscite). The main functionality of the software will be to control 2 SPI peripherals (one Master and one Slave). the iMx6 is connected to an FPGA with the two SPI. both driver for Linux shall be developed and tested we have the dt...iMX6 hardware platform (Variscite). The main functionality of the software will be to control 2 SPI peripherals (one Master and one Slave). the iMx6 is connected to an FPGA with the two SPI. both driver for Linux shall be developed and tested we have the dts and rootfs, and we already started testing of he Master SPI (we will share code). SPI Slave has to be developed from scratch OS built with ...

Looking for an experienced embedded Linux developer to help with the issue. The devices uses raspberry pi 3B+ and a TFT LCD in RGB mode as display and I run Qt’s distribution (b2qt) on it. When I enabled the logo support in Linux, no LOGO is displayed during kernel boot through TFT LCD. Moreover, the rainbow test does not show even though splash is not disabled. (but it worked on HDMI).

I am looking for a skilled developer to create a Linux Yocto project for the NXP Imax8. The project requires the following features: - Install linux Debian OS - Install QT support library - and peripheral driver Link of Hardware Hardware requirements for the NXP Imax8 are specified. - Licensing for this project should be Open Source. Ideal skills and experience for this job include: - Proficiency in Linux Yocto project development - Experience with NXP Imax8 hardware - Strong knowledge of multimedia, networking, and security features in Linux - Familiarity with Open Source licensing.

...write code for reading temperature data from a thermocouple sensor. - The temperature sensor must be wired, not wireless. - We are using Ardunio IC for reading it - We just want the code showing how you are reading the temperature from the thermocouple Needs to start immidiately and deliver fast Skills and Experience: - Strong background in embedded systems and programming. - Proficient in working with thermocouple sensors. - Knowledge of coding languages such as C or C++. - Experience with hardware interfacing and microcontrollers. - Ability to accurately read and interpret temperature sensor data. - Attention to detail and ability to write clean, efficient code. Deliverables: - Complete code for reading temperature data from the thermocouple sensor. - Do...

Write an initialization script using Yocto that will allow target machine (SAMA5D27) to automatically boot and run custom application at power up, preferably using systemd.

I am looking for an experienced embedded Linux developer to help me with my project. The target hardware platform is the Raspberry Pi, and I need a custom bootloader with features for network booting, encryption support, as well as an IP discovery tool. The project must be completed within 3 months. I need a talented developer who can leverage the Yocto project to create the custom bootloader and get it up and running. The bootloader should be tailored to the specific needs of my project. Furthermore, I would like support for debugging capabilities should any issues arise during the development cycle. I'm looking for a reliable and experienced developer who can work within my specified timeframe and deliver an exceptional product. If you think you have the needed skills ...

I am looking for a Unity programer who can help me to add control API using websocket or REST and build Uinity. I have a unity project programmed for webGL but needs to convert for Ubuntu and Windows changing JShook to API

I have a small craft distillery and am interested in using thermocouples to monitor temperatures from up to 14 locations 8 to start with. The programmer can select the thermocouples and data collector/transmitter. Data Display A monitor will be displayed on the wall of the distillery which will read out the current temperatures of each thermocouple and pressure sensor in larger readable numbers against an image of the equipment. User App/WebSite Users can also login to a web page remotely to: • View current temperature and pressure readings. • Create load and save different profiles configured allowing for user defined notifications (screen, text, email for determined temperature readings) Example - Profiles for Vodka, Whiskey, Stripping, Brandy Finishing, Moons...

I am looking for a freelancer with experience in using Yocto on a SAMA5D27 board. The specific version of Yocto we will be using is Kirkstone. The ideal candidate should have a strong background in Yocto configuration and experience working with SAMA5D27 boards. Basically, I have a modified ".dts" file and I need to rebuild the kernel and update the necessary files (.dtb, .itb, its) in order to boot successfully on the SAMA5D27 evaluation board. In addition, what I am looking is for a candidate to develop a detailed procedure on how to accomplish this having a new .dts file at hand.

I am interested in finding a freelancer to help me with a Yocto project on a SAMA5D27 board. Although I have limited experience with Yocto, I do have a good understanding of embedded Linux. I need help customizing the kernel on the board by rebuilding it using a modified device tree source (dts) file. The main purpose of this project is to reconfigure and rebuild the kernel so it functions properly on the board with the updated dts file. Assistance may be needed with certain hardware peripherals, though I am familiar with the hardware and may need assistance later.

Arduino Portenta Machine Control Thermocouple breakout

I have dome data Need to write It's about circuit with op amp and determine eutectic point with thermocouple, along with some statistical metrics (such as confidence intervals and error bar on graph).