Fpga xilinx vhdl jobber
We are looking for Smartfusion A2F-Eval Kit experienced engineer for our Inkjet Project. We firstly implement the project using those kit, then we want to get...computer sends config data (25 items, each of 2 byte) to kit with USB and stores in it as lookup table. 2. Storing data from USB to memory: a computer sends data ( less than 32K size) to kit with USB. M3 processor captures the data and writes to internal memory. 3. Analog output : FPGA reads the data which mentioned at 2. For each bit of those data, the program get the voltage value from lookup table and send the signal using internal DAC output. Frequency of analog output should be at least 75 KHz. So, FPGA should read each bit, lookup corresponding the voltage value from table and put into DAC should be finished ...
Hi freelancers Looking for electronics engineers having good experience in following modules: • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM32. • Drivers (GPIO, UART, SPI, I2C, PWM....) • IDEs like Keil MDK V5, ATmel studio and MPLab XC8.
I have a lot of works related to different fields of electrical engineering looking for experts in following areas: • Embedded C Programming. • VHDL/Verilog • Microcontroller like Arduino, Raspberry Pi, FPGA, AVR, PIC and STM32. • IDEs like Keil MDK V5, ATmel studio and MPLab XC8. • PLCs / SCADA • PCB Designing-Proteus, Eagle. • Multisim • IOT Technologies like Ethernet, GSM GPRS. • HTTP Restful APIs connection for IOT Communications.
I need to open an image, filter it with gaussian filter, then get the output through VGA Port. I have a Spartan 3E-100 CP132 with me, and I need to run the code over it.
I have various projects with different needs. Some more software focus; others more hardware focused. However, all projects have the end goal of FPGA parallel compute acceleration for imaging and graphics applications. I'd like to start anyone that is interested off with a short term project. Then if a fit is mutually made move on to more short term or a longer term projects. I'm open to various hours/schedules that work best for you.
I have a spartain 11 fpga board design (eagle .brd) since 2005 that I need to generate a sch file for.
A reliability enhanced video storage architecture in hybrid SLC/MLC NAND flash memory
It is a serial data splitter from 1 input source to 16 output sink using FPGA with specification as below: * synchronous data transfer * simplex data transfer (from source to sink), using TxD, RxD, TxClock , RxClock * there are 2 modes of clock operation which is selectable using gpio pin : external clock source or internal clock source * data buffer for input and all output channel * preferable to use low cost FPGA : Altera Cyclone II EP2C5T144 or you can recommend another low cost FPGA type
I want to implement a face recognition algorithm on Xilinx pynq z2 or a zedboard card.
FPGA project using VHDL about sequential logic circuits, details will be provided
Need someone to help me with selecting a fpga board and designing the SOC. If you are prepared the design or coding in this field I would invite you our project.
Tutoring for easy FPGA programming tasks in Labview FPGA modul and/or Xilinx Vivado.
Technical description of LVDS as comparator and explanation of LVDS behaviour for the values obtained by comparing two signals.
You are required to make a code that takes an input from the user , changes the clock frequency using that input and gives the user 3 guesses to find the changed clock frequency the code is for a Spartan 3A FPGA
The goal is to make a project where we have 2 pictures: 1 from ov7670 and 1 from pc, applying green screen effect to the 1st one (the picture will be taken with the green background), changing the green pixels with the 2nd picture and then see it on pc by uart or vga. The codes are needed to be in VHDL. I don't need a great resolution for pictures, 160x120 pictures with 8 bit or 16 bit colors would be sufficient.
Diseño IC modulo sincronizador GNSS nulti-satelites. y modulo sincronizador GSM/GPRS 2G y 3G multi-bandas.
i need the help of an expert who is very good to help write a VHDL code for a very simple system,i need it urgently, many thanks
It is a project to write a VHDL code and implement on a 7 segment display. Attached is complete description of all the requirements
O freelancer deverá conhecer as linguagens = C / vhdl / verilog e já ter trabalhado com FPGA / ASIC Portar e otimizar um código que já tenho pronto em "c" para vhdl ou verilog esse código gera uma string de 14 / 15 dígitos, será usado uma placa fpga xillinx spartan 6 ( a empresa xillinx disponibiliza todo o ambiente necessário ). converter a string em Sha256 usando placa asic depois de convertido em sha256 compara com um sha256 informado no inicio do processo, se igual finaliza, se não reinicia o processo. Deverá ser usado a Raspberry Pi 3 para termos uma interface ( teclado e monitor ) para inserir o código inicial
A reliability enhanced video storage architecture in hybrid SLC/MLC NAND flash memory
Project goal is designing 4x4 binary multiplier with shift & add algorithm. Stricted rules: Project must be prepared with Verilog [Vivado Design Suite] (System Verilog and VHDL is not acceptable) I need circuit design, Verilog models and basic report (Explanation of how things work, schematics, verilog codes etc) If you're interested, I can share detailed pdf of project with you.
Budget: CAD $20-30 Time: 1-3 Days Need to design a segment display in VHDL.
Hello Experts Looking for good digital electronics expert with knowledge of verilog, fpga , mips etc to work on small project today 9th dec. Apply only if you are available to help today Thanks
Hello Experts Looking for good digital electronics expert with knowledge of verilog, fpga , mips etc to work on small project today 9th dec. Apply only if you are available to help today Thanks
Hello There Need very good digital electronics based expert to help on small project today ie 9th Dec. If you are good with verilog, FPGA, MIPS etc then apply only. You ll be hired asap if you are sure you'll help today
Hello There Need very good digital electronics based expert to help on small project tomorrow ie 9th Dec. If you are good with verilog, FPGA, MIPS etc then apply only. You ll be hired asap if you are available to start on 9th dec Thanks
Hi, I am looking for someone who can capture a 16 bit data from input of the picoblaze processor and add some constant value into it and give the result on output. No need to verify on board, only testbench simulation is accepted in VHDL.
For this project the goal is to design and simulate a Blackjack game using Verilog/VHDL. It must be demonstrated using the Mimas Spartan 6 FPGA board. The inputs are taken from the player using the switches and push buttons while the output is displayed on the LCD display and LEDs.
Hello Need very good digital electronics based expert to help on small project tomorrow ie 9th Dec. If you are good with verilog, FPGA, MIPS etc then apply only. You ll be hired asap if you are available to start on 9th dec Read Less
Hello Need very good digital electronics based expert to help on small project tomorrow ie 9th Dec. If you are good with verilog, FPGA, MIPS etc then apply only. You ll be hired asap if you are available to start on 9th dec
Hello Need very good digital electronics based expert to help on small project tomorrow ie 9th Dec. If you are good with verilog, FPGA, MIPS etc then apply only. You ll be hired asap if you are available to start on 9th dec
Need VHDL code This project consists of two main components. A counter programmed with VHDL and an ALU based on MicroBlaze running a C code to perform ALU functionality. 1. This project requires the students to implement a 10-bit counter design using VHDL. The counter will have the ability to count up and down from 0 and 1000. This requires the utilization of 16 slide switches and the center push button of the Basys3 board. The 10 right- most switches (SW0 – SW9) will be used to input a preset value to the counter or the ALU. SW0 represents the LSB and SW9 represents the MSB of the input value. The center push button (BTNC) is used as the manual clock for the counter. The count should increase or decrease (depending on the selector switch, SW13) by 1 on every ris...
I need help with completing the design of a simple general purpose processor using Xilinx ISE Schematic Capture.
Hardware implementation of elliptic curve over binary field 163 field , with UART using VHDL and the platform is virtex 5
I already have 7 segments running but i need help in modifying the code and adding the temperature sensor. Ready to pay 5000 rupees for this job.
I want to design simple cut down processor in Xilinx. I will provide complete details in chat.
The project here is to write multiple conditions/actions using VHDL format, that can all be displayed in 1 single program. And tested on an Altera DE2 board Port mapping could be okay but using relatively basic principles is ideal. That is (all are not required): Case statements Else / ElseIf Signals Variables Shift register Flip Flops Multiplexer / De-multiplexer Multibit adder Along with the code, pin assignments should be completed.
Grin 31 bitstream and miner fpga and I have a choose between to different ones. Need ur opinion on which one is better for a ROI
Grin 31 bitstream and miner for the fpga. So I a choose between the Sqrl Forest kitten vu33p and Junglecat with dual vu9p which is going to have a better ROI ??
I need a design implemented that utilizes the Altera Max 10 FPGA (document with pins attatched) as a decoder to have an Analog Potentiometer (A/P) control RGB LEDs (document attached). Ideally the potentiometer would control the brightness of one of the colors and be able to switch between red, green, or blue. This does not need to actually be programmed onto the board. The schematic, code, and test benching just needs to be done. In addition, I need a brief description of what your inputs/outputs on your design are doing and how the decoder works. What you will provide (An example of your results is shown) - TOP Level Schematic for A/P to RGB LED - Decoder System Verilog Code - Test Bench (Model Sim) for A/P to LED RGB LED Data Link:
Hi, I am looking for help with a VHDL project. Project is create a combinational lock system using VHDL. Lock will open when entered passcode is correct and message "O" will be display on LCD. If entered passcode is not correct, then lock will not open and message "L" will be displayed on LCD. If user enters wrong passcode more than 2 times, then RED LED should Blink. VHDL code should also allow the user to change password. I am using Xilinx ISE Design Suite 14.7 and Vertex 5 XC5VLX50 board to do the demo to my instructor. I am have started it using a State Machine. Please help by adding/improving the attached code. I need it very urgently. Thank you!
Need a code on nexus 3 fpga board to turn on and off 2 leds using 2 switches.. Switches and leds are ilexternal not on board
I need a design to be theoretically implemented that utilizes the Altera Max 10 FPGA (document with pins attatched) as a decoder to have an Analog Potentiometer control RGB LEDs (document attached). In addition, I need a rough description of what your inputs/outputs on your design are doing and how the decoder works. What you will provide (An example of your results is shown) - TOP Level Schematic for A/P to RGB LED - Decoder HDL - Simulatation for A/P to LED RGB LED Data Link:
I am looking for someone who can fix errors and complete my program. I was planning on using C code within the SDK within the vivado program to connect my two slave codes. I'm fine with using a master IP if need, if you can't figure out how to code in C within the SDK. I created two slave IPs.
We will create a side scrolling game Lets do something similar to Mega Man, zelda, mario Style of game will be scrolling both vertical and horizontal
Hello, i want someone to design a device (frequency generator) that produces multiple accurate frequencies. This device will communicate with a smartphone app and a site you will develop. I need an expert in these fields, pcb design fpga programming, app mobile programming, website development and communication those 3. So the project includes 3 parts. 1. The device. 2. The mobile app. 3. The website. for this project i need a prototype. There is a file with the requirements uploaded.
Hi Smith J., As discussed on "https://www.freelancer.com/projects/arduino/Embedded-system-FPGA-verilog-code-22644894/proposals", please start work
