Esp32 datasheetlavori

Il mio progetto consiste nel controllare tramite un modulo ESP32 DEVKIT V1 un motore brushless. Sul modulo ESP32 ci sono montati due pulsanti, uno sul pin 18 per aumentare la velocità del motore, l'altro sul pin 19 per diminuire la velocità del motore. Il motore è collegato ad un ESC il quale è collegato tramite il pin 9 ad una arduino UNO. Sulla arduino UNO è inoltre montato (pin RX e TX) un modulo HC-06 (indirizzo mac: 98:D3:31:FD:2D:B5 , pin: "1234"). Obbiettivo è quello di avere i codici (uno per ESP32 e l'altro per Arduino UNO) che mi permettano di collegare l'ESP32 all'HC-06, di poter inviare segnali di aumento e diminuzione di velocità al motore. Nella posizione iniziale il motore dov...

...numero di accessi rimanenti: Accessi zero: LED rosso e suono lungo. Accessi disponibili: LED verde e doppio suono corto. Specifiche tecniche: Protocollo di comunicazione: MQTT o altri su valutazione Dispositivi di Interfaccia: NFC Feedback visivo: LED (Rosso/Verde) Feedback sonoro: Suono lungo e doppio suono corto Controller: Client: Lettori NFC: MF RC522 Buzzer: Obiettivi: Creazione interfaccia per il controller Facilitare la gestione centralizzata dei dispositivi connessi.

...è collegato ad Arduino Nano Esp32 - QMC5883L comunica con Arduino Nano Esp32 via I2C - QMC5883L deve misurare in continuo le tre componenti di campo geomagnetico (almeno 2 misure al secondo, frequenza deve essere personalizzabile), e confrontare la lettura attuale con quella precedente, per vedere se vi sono variazioni di campo oltre una soglia da impostare - Mentre QMC5883L misura, Arduino Nano Esp32 deve rimanere in deep sleep - Se e solo se viene rilevata una variazione oltre la soglia impostata, allora Arduino Nano Esp32 deve ricevere segnale di wake up, stampare su schermo le componenti del campo appena lette e tornare subito in deep sleep. - Una volta tornato in deep sleep, QMC5883L ricomincia a misurare Dovendo il sensore misurare mentre Arduino...

Salve alespitfire, Avrei necessità di finire un progetto basato su esp32 per il controllo di un motore stepper nema 17 che dovrà girare indipendentemente da tutto in background. Un display LCD 2.4" ILI9341 (o similari) con visualizzazione di dati provenienti da sensore di pressione i2c, due schede HX711 che dovranno rilevare la flessione sull'asse motore e l'altro dovrà rilevare un valore limite di sicurezza sul telaio dove è fossata la cella di carico corrispondente. Sensore di hall e BT.

Salve Paolo, Avrei necessità di finire un progetto basato su esp32 per il controllo di un motore stepper nema 17 che dovrà girare indipendentemente da tutto in background. Un display LCD 2.4" ILI9341 (o similari) con visualizzazione di dati provenienti da sensore di pressione i2c, due schede HX711 che dovranno rilevare la flessione sull'asse motore e l'altro dovrà rilevare un valore limite di sicurezza sul telaio dove è fossata la cella di carico corrispondente. Sensore di hall e BT.

Ho bisogno di un software che scatta una foto con ESP32 CAM e la invia attraverso sim800 in FTP su un server cloud gia' in mio possesso. Grazie.

Ciao Michele, per questioni di velocità avvio app (no piu' boot time) dovrei passare dalla piattaforma raspberry pi ad un microcontroller piu' veloce nelle fasi di avvio App. Dovrei far eseguire il miei script già in Python 3.7 in micropython . In Python 3.7 uso la semplice e ottima libreria minimalmodbus (sempl...Michele, per questioni di velocità avvio app (no piu' boot time) dovrei passare dalla piattaforma raspberry pi ad un microcontroller piu' veloce nelle fasi di avvio App. Dovrei far eseguire il miei script già in Python 3.7 in micropython . In Python 3.7 uso la semplice e ottima libreria minimalmodbus (semplice lettura e scrittura di registri). Se possibile vorrei eseguirlo in micropython su ESP32. Se ci sei ci possiamo...

cerco qualcuno che sappia interfacciare il nextion con l esp32 e che sappia quindi crearmi una grafica di visualizzazione dei dati ricevuti dai sensori e poi serve la creazione delle pagine per il setting delle impostazioni che comandano le azioni per modificare i valori ecc ecc ..

La finalità del progetto consiste nella realizzazione di un sistema di lettura sensore livello acqua di una vasca , temperatura con Esp 32 e trasmettere dati con protocollo LoRawan ad un altro Esp32 , il secondo dovrebbe trasmettere i dati a sua volta ad una Raspberry che farà da webserver .Sulla rasperry ci deve essere pagina internet con grafici e storici interpellabili da remoto.

Devo aggiornare lo sketch di molti dispositivi ESP32 sparsi in varie località remote, ciascuno è collegato ad una rete wifi locale. grazie mille

ho bisogno di una figura che mi aiuti a sistemare i manuali d'istruzioni ed I datasheet di una gamma di prodotti.

logo azienda laboratorio di saldatura italiana denominazione COROMAN. Uso del logo su format tecnico come datasheet, brochure,

>Registrati o accedi per visualizzare i dettagli.

I am seeking an experienced deve...user-friendly interface for managing orders, without any initial need for POS integration. Additionally, the system will require hardware support for ESP32-based setups, which will be used for microphones and speakers. Key Features: - Voice recognition for both phone and table-based orders. - A straightforward dashboard for order management, or use of ready made like Gloria Food. Ideal Skills and Experience: - Prior experience with AI and voice recognition systems, especially Chatgpt Api. - Familiarity with Azure STT/TTS services, or similar. - Expertise in creating user-friendly interfaces. - Knowledge of hardware compatibility, particularly with ESP32, or similar. Please include your experience, estimated timeline, and cost ...

...microchip for UART, SIM800L (GSM), and NEO-6M (GPS). The design should also accommodate a buzzer, mini LEDs, and USB-C charging, with provisions for battery integration (details to be finalized). Key Tasks: - Optimize the antenna design for GSM and GPS to ensure the best performance. - Create compact and efficient layouts that can withstand the rigors of a prototype. - Transition existing code from ESP32 to STM32. Key Considerations: - The primary focus of the PCB design is compactness. The smaller the PCB, the better. - The IoT device will be powered by a rechargeable battery, so consideration for this power source is crucial. - GPS accuracy is the most critical feature of the device, so the design should facilitate this. Ideal Skills and Experience: - Proven experience in P...

We have around 80 ESP32 based wireless devices in a center. These devices communicate with our local server which is assigned a static IP. We have a live TCP socket from each of the device to local server. This socket reattempts connection if device doesnt hear from server for 20sec. Everything runs smoothly for a period of time and then suddenly devices start disconnecting and reconnecting to this TCP socket. This goes on for around 1hr or so and then most of the time situation self resolves. If we restart the access point/router we see improvement in the situation but it does recur. During the period of 'reconnections' even HTTP requests from devices to server start to fail. Pings from server to device IP times out too. We can see in access point that the device is stil...

I'm looking for an experienced electronics engineer to design and code a circuit board that can control both analog RGBW LED strips and digital addressable LED strips (like WS2812) using an ESP32. Key Responsibilities: - Design a circuit board compatible with both types of LED strips - Code the ESP32 to control the LED strips - Ensure the circuit board can perform static color displays on the LED strips Ideal Skills: - Proficiency in circuit design and coding - Previous experience with ESP32 and LED strip control - Ability to create a robust and efficient circuit board Please note, there is no need for the circuit board to support any wireless control options or music synchronization. The primary focus is on controlling the LED strips to display static colors.

I need an ...designed for speed control using PWM (Pulse Width Modulation). The whole project will be powered by a 12V-14V car battery. One motor have 10A max current and the other one have 60A max current. The whole project is controlled by an ESP32 micro controller. Also i would like to integrate a 12V to 5V stepdown converter to power the ESP32. Key requirements: - Add relay motor control for forward and reverse motion. - Incorporate speed control for one motor with PWM. - Integrate overcurrent protection into the PCB design. - Integrate 5V stepdown converter for ESP32 Ideal candidates should have: - Strong background in PCB design and motor control systems. - Proficient knowledge of relay-based motor controllers and PWM. - Experience with implementing protective...

Hi there I did read your project description and it looks you are looking for an electronics engineer having experience in circuit, PCB layout designing, and microcontrollers coding/firmware development. My name is Engr. Saddam Gul, I am an electronics engineer having 5+ years of experience in circuits designing, PCB layout designing, and embedded system microcontrollers (Arduino, ESP32, FPGA, C2000, STM, and Rpi) coding/firmware development. I have successfully executed numerous complex projects, which you can view in my portfolio as samples. Please feel free to share more details about your project, and don't hesitate to contact me for any further discussions. Thank you Regards Engr. Saddam Gul

I'm looking to set up an ESP32 that communicates with a backend server over MQTT using .NET Core 9 and SignalR. The primary objective is to enable remote control of devices, with additional functionality for real-time monitoring of sensor data, such as temperature and humidity. Key Requirements: - Establish a Wi-Fi connection for the ESP32. - Implement the MQTT protocol for communication. - Set up SignalR for real-time updates. - Use .NET Core 9 for the backend. Ideal skills would include: - Proficiency in working with ESP32 and MQTT. - Experience with .NET Core and SignalR. - Knowledge of Wi-Fi connectivity and sensor data handling. - Prior work in remote device control projects. Please include relevant experience in your bid.

I'm looking for a seasoned professional with extensive experience in working with the ESP32 and cellular network connections. The goal is to set up a web server on the LILYGO T-SIM7000G ESP32 that can be accessed via a public static IP address. This project involves configuring the server to serve static files (HTML, CSS, JS) and handling real-time data updates. Key Responsibilities: - Configure the ESP32 to serve static web content and handle real-time updates. - Enable the ESP32 to process query/response data to a serial device. Skills and Experience Required: - Deep understanding of ESP32 and LILYGO T-SIM7000G. - Proficiency in Arduino IDE. - Previous experience in setting up web servers on ESP32. - Familiarity with AT commands and the ma...

Necessito de alguem que consiga auxiliar em um projeto de um detector de fumaça controlado por arduino esp32 que se comunica com dispositivos celulares.

I'm looking for a skilled ESP32 C++ developer who can assist in configuring a monitoring device to track health metrics, specifically glucose levels. The device needs to be able to connect to some API/Webservices and display a value based on the return data Key Responsibilities: All configured via touchscreen Users will be able to select Wifi network via esp32 touchscreen - this gets them started They will then select which brand of glucose tracker they have The users will then insert there login credentials as required by the API And once logged in the monitor will display there current glucose levels as retrieved by the API , this will be a contious display on the screen showing nothing but a number - along side an indicator to show if the value is rising or dec...

I'm looking for a designer to create a 3D printable file for a custom ESP32 enclosure. The design should be based off an existing model () but will need some modifications. Specific requirements: - The enclosure should have a domed circular cover plate about 250mm in diameter.( I have some sample ideas that i can share) - It should include ventilation holes and mounting brackets. - The design should incorporate a custom logo on the front that will be a cutout. (Logo to be provided to the freelancer upon request) Ideal freelancer skills: - Proficiency in CAD software. - Experience with 3D printing design. - Ability to create custom logos in CAD. - Knowledge of materials and finishes suitable for 3D printing. (I have attached a sample of a similar

I need a PCB designed for the ESP32 S3 DevkitC-1. This is a prototyping project, so the design should be flexible and adaptable for different uses. i have provided the image ,design will have to be like that but with 44pins and screw terminals(22-left & 22p right) socket to plug esp32 s3 devkit c1,male jumper wires connector,and above mentioned screw terminal Key Requirements: - Design a custom-sized PCB, tailored to specific dimensions - Prototyping-focused design, allowing for adaptability - Knowledge in working with ESP32 S3 is a plus Ideal Skills: - PCB design - Experience with ESP32 S3 - Understanding of prototyping needs - Ability to work with custom size requirements

Project Description I need a professional hardware/electronics designer to create a complete ESP32-S3-based pcb. The design will feature: - ESP32-S3 module (placed on edge side of the PCB) with USB-C for programming. - 18 high-resolution analog inputs for NTC 10K/20K/100K sensors with shared COM pins. - 8 solid-state relay (SSR) outputs for controlling contactor signals, with shared COM pins. - One high-reliability 0-10V analog output. - Ethernet port with the W5500 IC and RJ45 connector at the bottom edge. - Integration of an external RTC module (DS3231) with battery backup for accurate timekeeping. - Power regulation, protection circuits, and optimized PCB design. - Milled slits for isolating I2C sensors.

I need a seasoned PCB designer to create a personal navigation device using an ESP32-S3. The low-power design will encompass various components such as a GPS, sensors buttons, and connectors. Key Features: - Incorporate ESP32 WROOM S3 and u-blox MAX-M10S GPS with chip antenna - Integrate a Speaker and 5 Pushbuttons - Include a Micro SD Card Slot and USB-C Connector - Have a Barometric Sensor, Accelerometer/Gyro, and Ambient Light Sensor - Implement a LoRA Radio and 4 connectors for battery & peripherals - Support LiPo charging and power management Board Dimensions: Approximately 44mm x 72mm Deliverables: - Altium Designer Schematic - Detailed Parts List (BOM) with supplier information - Altium Designer PCB Layout - Complete Fabrication data (Geber files etc) ...

I need an expert who can interface a USR-TCP232-T2 with an ESP32 in order to send sensor data to a website using GET and POST requests. just get and post requst demo will do the job any available api

I'm...Squareline Studio editor. The primary aim is to empower my engineers (who aren't software engineers) to design a GUI within Squareline, generate the code, and upload it to an ESP32 using the Arduino environment. Key project components: - The GUI should incorporate buttons and sliders as the main graphical elements. - The ESP32 should be capable of controlling devices, monitoring data, and triggering events through the touchscreen. - Utilization of the LittlevGL (LVGL) library in conjunction with Squareline Studio is necessary. Ideal candidates for this project should have: - Extensive experience with touchscreen integration and ESP32 microcontrollers. - Proficiency in Squareline Studio and the LVGL library. - Ability to simplify complex programming co...

I'm looking to design a technical datasheet focused on product specifications. The final output should be a well-structured PDF that includes: - Diagrams/Illustrations: Clear and informative visuals that help convey product features and specifications. - Technical specifications table: A detailed and accurate table outlining all key product specifications. - Usage instructions: Simple and easy-to-follow instructions on how to use the product. The ideal freelancer for this project should have experience in technical writing and datasheet design. Proficiency in graphic design for creating diagrams and illustrations is a plus. Please provide examples of similar projects you've completed in your proposal.

I need a technical datasheet designed for a radio. The datasheet should be minimalistic in style and include: - Technical specifications: Detailed information about the radio's capabilities and features. - Usage instructions: Clear and concise directions on how to operate the radio. Ideal skills for this job include graphic design, technical writing and a strong understanding of minimalistic design principles. Experience working with electronics datasheets will be a significant advantage.

I need a technical datasheet designed for a radio. The datasheet should be minimalistic in style and include: - Technical specifications: Detailed information about the radio's capabilities and features. - Usage instructions: Clear and concise directions on how to operate the radio. Ideal skills for this job include graphic design, technical writing and a strong understanding of minimalistic design principles. Experience working with electronics datasheets will be a significant advantage.

Creating a Datasheet of around 10 Pages. With multiple changes in design allowed

I need an expert in ESPHome and ESP32 boards to assist with creating YAML code for controlling a servo via ESPNow. Key Requirements: - The main purpose is to automatically control a servo from 0% to 100% then return to 0% after 1s using an ESP32. This will happen when a photoelectric retroreflector switch is triggered on a different ESP32 board. ( When switch is triggered on one ESP32 board 1. The servo on ESP32 board 2 should instantly changes to 100% position and returns to 0% after 1s) - The communication between ESP32 devices should use the ESPNow protocol. - The yaml code should be suitable for ESPHome. - The ideal freelancer will have extensive experience with ESPHome, ESP32 boards, and ESPNow. I’m an electrical engineer w...

lets' fix my broken code...

Per our PMs, correct the existing code to enable the NEO 8M gps module to deliver data to serial monitor

My project involves troubleshooting an ESP32 Arduino code that integrates with a NEO-8M GPS module. Currently, the GPS data is not appearing on the serial monitor and this issue needs to be rectified. Key Requirements: - Maintain the original code structure and logic while debugging. - Modify the code to output full GPS data (including time and date) to the serial monitor. - Ensure that the GPS coordinates are accurately displayed. Ideal Skills and Experience: - Proficient in Arduino programming, particularly with ESP32. - Experienced with NEO-8M GPS module integration. - Strong debugging skills to identify and fix code issues. - Able to maintain the integrity of the original code structure and logic.

Correct code to enable GPS module to work with ESP32 and LVGL

Per our conversation, ESP32 GPS code correction

Per our conversation, ESP32 GPS code correction

...user interface programming project in MicroPython and FreeRTOS, that should work with a screen on the parallel port. The user interface should send pre-written commands to the DAC 8760 via SPI and read a voltage via I2S. The project has a PCBA part and a Firmware part. The major part is firmware development for UI and the PCBA part is just to test the UI. The Stimulation running page, where the ESP32 will send 700 commands per second to the DAC, during 20-60 minutes, But it should manage to responds without delay the user interface command while sending the commands to the DAC and refresh properly the screen. Note: There is no need to code the functional that will generate the different signal parts in the stimulation Running Page. Just make the UI and complete the applyStimu...

I am in need of a microcontroller expert who can convert my current setup (ESP32, SIM800L, Neo6M GPS) into a more compact design using the STM32G030F6P6TR chip and embed it with a SIM868. The goal is to create a compact, efficient, and versatile tracking device. Responsibilities: - Convert the existing microcontroller setup to an STM32G030F6P6TR chip. - Embed the design with the SIM868 for enhanced functionality. - Design a PCB that accommodates this compact design without compromising performance. - Ensure the device is suitable for both indoor and outdoor use. The device needs to support real-time tracking functionality. Therefore, experience in designing tracking devices is preferred. Please note, I require only qualified professionals to bid on this project. Proposals genera...

I'm looking for a skilled developer to design a control system for 22 ESP32-CAMs. The system should display all camera streams on a single web-based interface, compatible with Windows OS. Below each stream, there should be a 3-position toggle switch. These switches need to control a 32-channel relay board over WiFi, using the Modbus protocol. Key Requirements: - Static ESP32-CAM streaming code - Modbus and relay modules code - Full setup code for the system - Implement user authentication via username and password Ideal Skills: - Extensive experience with ESP32-CAMs - Proficiency in Modbus protocol - Strong background in relay board control - Expertise in designing secure web-based interfaces - Excellent understanding of coding for static streams.

I'm seeking a skilled professional to assist with integrating my Guition ESP32-S3-4848S040 board into SquareLine Studio for the Arduino IDE. The ultimate goal is to produce a complete set of files that adhere to the specified requirements. Here are links to descriptions of a board, specifically mine is ESP32-S3, ST7701, GT911, and requires the CH340 driver: General description: Additional information about the board: I am looking for a fully functional set of files for SquareLine Studio that meet the requirements outlined below: Ideal Skills and Experience: - Proficient in C/C++ programming - Experienced in

I need an advanced ESP32 developer to help me connect a 3.5mm headphone with mic to an ESP32 and turn it into a hands-free device for calls. I have a full working example at the provided Github link. However, this example expects an external DAC or codec. I want to use the internal DAC and ADC and connect to a TRRS adapter. Your guidance and code will be crucial for this project. Working code But this assumes an external dac and adc according to my knowledge I want to use internal one and connect it to the 3.5mm adapter. I need a circuit diagram and code. Key Requirements: - The device must support answering and ending calls. - Expertise in ESP32 development is a must. - Previous experience with

I'm in need of an experienced developer to create a few small, custom ESP32 projects for me. The project involves building IoT devices with the following essential functionalities: - WiFi connectivity: This is crucial for the device to connect and communicate within a network. - Sensor integration: The device should be able to integrate with various sensors for data collection and processing. - Storage: The device needs to have a storage solution for data logging and retrieval. - Speaker: This will allow the device to produce sound. - GPS: The device should be able to track its location. Ideal candidates for this project would be those with a strong background in IoT device development, particularly with the ESP32. Experience with sensor integration, data storage solu...

I'm experiencing issues with my ESP32 code for LoRaWAN OTAA. Specifically, my device isn't able to join The Things Network (TTN). I've verified that my device credentials and configuration are correct, so I need an expert to help troubleshoot and resolve the issue. Ideal Skills and Experience: - Proficiency in ESP32 programming - Experience with LoRaWAN and TTN - Strong problem-solving skills - Ability to troubleshoot network connection issues - Knowledge of SX1276 module Please reach out if you can assist with this issue.

...Materials (BoM) outlining all components required for the design. o Gerber files for PCB manufacturing. o Firmware code with detailed comments and instructions. o Documentation for circuit schematic, firmware installation, and setup. Skills Required: • Experience in PCB design (schematic creation, component placement, routing). • Strong background in embedded firmware development for microcontrollers ESP32. • Expertise in sensor integration (moisture, temperature, light). • Proficiency in designing and controlling displays (LCD, OLED, etc.). • Knowledge of low power design techniques and energy-efficient systems. • Familiarity with developing interactive user interfaces. Please submit your portfolio with relevant examples of PCB designs and firmwa...

I'm looking for a arduino firmware engineer to create a firmware for an ArtNet node with DMX/RDM support based on the RP2040 + RS485 transceiver. This project is similar to the typical artnetnodes available on GitHub for ESP32 or ESP8266. Key Responsibilities: - Develop firmware to support ArtNet4(Poll/Reply, ArtDMX, ArtRDM) as a gateway to DMX and RDM, with RDM handling efficiency as a priority for 1 universe/RS485 connection - Ensure the DMX settings are fixed for maximum performance for RDM, with only 1-2 DMX frames per second. - Implement USB network communication instead of WiFi (with DHCP server on RP2040 and fix host adress 2.2.2.1 and 2.2.100+ for the PC client) - No web server for configuration required. Ideal Skills and Experience: - Extensive experience with ardui...

ESP32 Arduino Sketch and Google Sheets Script We are looking for a skilled developer to create a simple ESP32 Arduino sketch along with a script for Google Sheets. The purpose of the following system will be to determine when an ESP32 starts running and when it stops running and to determine how long it was running for and how long it was not running for. Create an Arduino sketch running on an ESP32. The sketch will send a message to a Google Sheet every ten seconds. Create a Google Sheet to receive the messages and record the time when messages are received. The first message after a period of not receiving any messages will be a start time. When new messages are received, the time elapsed between the start time and the current message will be calculated an...