iPhone 14 Plus Battery

Before You Begin

 Warning

  • A battery should be replaced only by individual technicians with the knowledge and experience to repair electronic devices. Improper battery replacement, improper handling of parts, or failure to follow the provided instructions could result in fire, injury, data loss, or damage to the device, parts, or other property.

  • Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Remove the following parts before you begin:

Tools

  • 6.7-inch repair tray

  • Battery press

  • ESD-safe cleaning solution

  • ESD-safe tweezers

  • Ethanol wipes or isopropyl alcohol (IPA) wipes

  • Heat-resistant gloves

  • Nylon probe (black stick)

  • Safety glasses with side shields

  • Sand

  • Sand container

 Caution

Avoid touching the TrueDepth camera assembly, grounding springs, or nearby parts.

Important

If you replace this part, it is recommended to run Repair Assistant in order to finish the repair. Repair Assistant will be available on the device after you’ve completed all reassembly steps.

Removal

  1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

    • Important: Some iPhone 14 Plus models may have a white adhesive shim under the battery flex cable. If you see a white adhesive shim (1), use ESD-safe tweezers to gently lift the flex cable from the adhesive shim (2). Then use the tweezers to remove the shim and discard it (3).

  2. Use ESD-safe tweezers to grasp the top right battery adhesive tab. Gently peel the adhesive tab away from the battery.

    • Warning: Don't scrape or puncture the battery with the tweezers.

    • Note: The battery has two adhesive tabs.

  3. Twist the tab around the tweezers and pull up 1 inch until you see white adhesive strip on the tweezers.

  4. Keep the tweezers close and parallel to the battery. Then pull the tweezers toward the top of the iPhone and continue to twist and pull the adhesive until you’ve removed the entire strip.

    • Caution: Don’t pull the adhesive strip against parts or screws.

    • Important: If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 4. If you can’t see the tab or strip, continue to the next step.

  5. Use ESD-safe tweezers to grasp the top left battery adhesive tab. Gently peel the adhesive tab away from the battery.

  6. Repeat steps 3 and 4.

    • Important: If the battery adhesive tab or strip breaks off and you can still see it, attempt to retrieve it with the tweezers. Wrap the tab or strip around the tweezers and repeat step 4. If you can’t see the tab or strip, continue to the next step.

  7. If both battery adhesive strips were fully removed, continue to step 10. If at least one strip was fully removed, continue to step 8.

    •  Warning: If both strips were broken and can’t be retrieved, don’t forcibly pry the battery. Stop the repair. You can find a service option at support.apple.com/repair.

  8. Insert the flat end of the black stick only into the insertion point as shown. Don’t insert the black stick into a point where the battery tab or strip is broken.

  9. Slightly lift the battery with the black stick just enough to grasp underneath the battery.

    • Caution: To avoid damage, don’t press the black stick on the edge of the enclosure as you lift the battery.

  10. Remove the battery from the enclosure. Then inspect the enclosure for damage. If the enclosure is damaged, replace the iPhone.

    • Warning: If you can’t remove the battery, stop the repair. You can find a service option at support.apple.com/repair.

Reassembly

  1. Use ethanol wipes or IPA wipes to remove all residual adhesive from the enclosure underneath the battery.

  2. Peel the pink release liner from the underside of the replacement battery.

    • Important: Don’t remove the protective cover from the top of the battery yet.

  3. Hold the battery over the enclosure with the protective cover faceup. Align the top of the battery with the camera sidewall (1) and the right edge with the logic board (2). Then lower the battery into the enclosure.

  4. The center of the repair tray has two slots. Position the repair tray and enclosure onto the battery press with one slot of the repair tray on one side of the battery press.

  5. Flip down the red lever at the top of the battery press to lower the roller onto the battery.

  6. Slide the repair tray back and forth through the battery press three times to adhere the battery to the enclosure.

  7. Flip up the red lever.

  8. Position the repair tray and enclosure to the other side of the battery press.

  9. Repeat steps 5 through 7. Then continue to step 10.

  10. Remove the repair tray from the battery press.

  11. Hold the edges of the protective cover. Pull the release tabs on the protective cover to remove the cover from the battery.

    • Important: Don’t press the area over the tab you’re releasing.

Reinstall the following parts to complete reassembly:

 Warning

Gently shake the iPhone. If the battery sounds loose, remove the back glass and the battery. Then complete battery reassembly with another replacement battery.

Important

  • A new battery is not charged. After you’ve completed all removal and reassembly steps, charge the device for a few minutes.

  • After you’ve completed all reassembly steps, Repair Assistant will be available on the device and is recommended to finish the repair. Learn how to initiate Repair Assistant.

Published Date: