iPhone 13 Pro Top Speaker (mmWave Antenna)

Before You Begin

Warning

Read Battery Safety and follow workspace and battery handling guidelines before you begin.

Important

If your iPhone doesn’t have an mmWave antenna, follow the instructions in Top Speaker.

mmWave antenna

Remove the following part before you begin:

Tools

  • 6.1-inch repair tray

  • ESD-safe tweezers

  • JCIS bit

  • Micro stix bit

  • Nitrile or lint-free gloves

  • Nylon probe (black stick)

  • SIM-eject tool

  • Super screw bit

  • Torque driver (black, 0.35 kgf cm)

  • Torque driver (blue, 0.65 kgf cm)

  • Torque driver (gray, 0.55 kgf cm)

  • Torque driver (green, 0.45 kgf cm)

Important

This procedure requires a battery protective cover. A battery protective cover is included with a replacement battery, top speaker (mmWave antenna), or TrueDepth camera. It's not a separately orderable part.

Caution

  • To avoid damaging the lenses, don’t touch the TrueDepth camera assembly or nearby parts.

  • Avoid the grounding spring on the camera cowling.

Removal

  1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

  2. Use a torque driver and the Micro stix bit to remove the four trilobe screws (1) from the camera cowling. Set aside the screws.

  3. Use a torque driver and the JCIS bit to remove the crosshead screw (2) from the camera cowling. Set aside the screw.

  4. Use ESD-safe tweezers to tilt up the camera cowling from the left side (1). Then slide the cowling tabs out of the slots on the right side of the enclosure (2). Save the cowling for reassembly.

  5. Use a torque driver and the Micro stix bit to remove the two trilobe screws from the logic board cowling. Set aside the screws.

  6. Use ESD-safe tweezers to remove the logic board cowling. Save the cowling for reassembly.

  7. Lift the ends of the 13 flex cables off the connectors as shown.

  8. Use a torque driver and the super screw bit to remove the two super screws from the logic board. Set aside the screws.

  9. Remove the enclosure from the repair tray.

  10. Insert a paper clip or SIM-eject tool into the hole next to the SIM tray.

  11. Push the paper clip or SIM-eject tool toward the enclosure to eject the SIM tray. Remove the SIM tray and save it for reassembly.

  12. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

  13. Use ESD-safe tweezers to push the SIM tray ejector into its original position.

  14. Put on the gloves.

  15. Gently hold the camera flex cables together and lift the cameras out of the enclosure. Save the cameras for reassembly.

  16. Use the flat end of the black stick to separate the adhesive between the mmWave antenna flex cable and the camera well.

  17. Place the battery protective cover on top of the battery.

  18. Lift up the logic board. Then rotate the logic board 45 degrees and place it gently on the protective cover.

    • Caution

      • Don’t damage the Apple Pay flex cable while moving the logic board.

      • Don’t damage the logic board while moving it. If damage occurs, replace the phone.

  19. Use a torque driver and the JCIS bit to remove the crosshead screw from the grounding strap on the top speaker. Set aside the screw.

  20. Use ESD-safe tweezers to remove the grounding strap from the top speaker.

    • Important: If you plan to replace the original speaker, set aside the grounding strap for reassembly.

    • Caution: Don’t damage the grounding springs on the grounding strap as you remove it. If damage occurs, replace the grounding strap.

  21. Use a torque driver and the JCIS bit to remove the crosshead screw (1) from the top speaker. Set aside the screw.

  22. Use a torque driver and the super screw bit to remove the two super screws (2) from the top speaker. Set aside the screws.

  23. Put on the gloves.

  24. Remove the top speaker from the enclosure.

Reassembly

  1. Put on the gloves.

  2. Use ESD-safe tweezers to position the top speaker in the enclosure.

    • Caution: Ensure that the gasket is in place on the speaker's top vent and not torn or damaged. If the gasket is damaged, replace the top speaker.

  3. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.

    • Caution: If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.

  4. Use the blue torque driver and super screw bit to install two new super screws (923-06271) (1) (923-06272) (2) into the top speaker.

  5. Use the green torque driver and JCIS bit to install one new crosshead screw (923-06273) (3) into the top speaker.

  6. Use ESD-safe tweezers to position the grounding strap on the top speaker.

    • Caution: Don’t bend or damage the grounding springs on the grounding strap. If damage occurs, replace the grounding strap.

  7. Use the green torque driver and JCIS bit to install one new crosshead screw (923-06273) into the grounding strap.

  8. Rotate the logic board and position it in the enclosure.

    • Caution: Ensure that no flex cables are trapped under the logic board.

  9. Remove the battery protective cover.

  10. Press the ends of 11 flex cables to the connectors in the order shown.

  11. Follow camera reassembly steps 2 through 8 to reinstall the camera. Then continue to step 12.

  12. Use the blue torque driver and super screw bit to install one new super screw (923-06293) (1) into the logic board.

  13. Use the gray torque driver and super screw bit to install one new super screw (963-06292) (2) into the logic board.

  14. Position the logic board cowling. Then use the black torque driver and Micro stix bit to install two new trilobe screws (923-06284) (1) (923-06286) (2) into the logic board cowling.

  15. Remove the enclosure from the repair tray.

  16. Press the SIM tray back into the side of the enclosure.

  17. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

Reinstall the following part to complete reassembly:

Published Date: