iPhone 14 Plus Back Glass

Before You Begin

Warning

  • Read Battery Safety and follow workspace and battery handling guidelines before you begin.

  • Read Broken Glass Safety before you begin.

  • Improper replacement, improper handling of parts, or failure to follow the provided instructions may cause malfunctions. Additionally, wireless charging may appear slow or the iPhone may not charge properly. These events could result in injury, or damage to the device, parts, or other property.

Tools

  • 6.7-inch heated display pocket

  • 6.7-inch repair tray

  • Adhesive cutter

  • Display adhesive press plate

  • Display press

  • ESD-safe tweezers

  • Ethanol wipes or isopropyl alcohol (IPA) wipes

  • Heated display removal fixture

  • Heat-resistant gloves

  • Micro stix bit

  • Nylon probe (black stick)

  • Safety glasses with side shields

  • Torque driver (black, 0.35 kgf cm)

  • Torque driver (blue, 0.65 kgf cm)

  • Torx security bit

Caution

To avoid damaging the lenses, don't touch the camera assembly or nearby parts.

Important

  • Read Heated Display Removal Fixture if you’re setting up the fixture for the first time.

  • If you replace this part, it is recommended to run Repair Assistant in order to finish the repair. Repair Assistant will be available on the device after you’ve completed all reassembly steps.

Removal

  1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

  2. Use a torque driver and the Torx security bit to remove the two security screws, one from each side of the Lightning connector. Set aside the screws.

  3. Flip the switch on the back of the heated display removal fixture to turn it on. The internal fan will turn on. Wait for a checkmark to appear on the screen.

    • Note: If an error code appears on the screen, turn off the fixture and turn it back on.

  4. Take the iPhone out of the repair tray. Then gently insert it into the heated display pocket with the camera faceup and the Lightning connector facing the bottom of the pocket.

    • Important: Ensure that the clamp on the side of the pocket is flipped up.

    • Caution: Don’t scratch the enclosure or the display as you insert the iPhone into the heated display pocket.

  5. Flip down the clamp on the side of the pocket to lock the iPhone into place.

  6. Put on the heat-resistant gloves. Align the cutout on the bottom of the pocket with the rail on the fixture. Slide the pocket with the iPhone onto the rail on the fixture.

    • Warning: Don’t insert the pocket into the fixture without wearing the heat-resistant gloves.

  7. Slide the pocket into the fixture until the pocket clicks into place.

    • Note: The screen on the fixture will turn red and the timer will count down from 2 minutes while the pocket heats to the correct temperature. When the timer shows 0, the fixture will start to beep and the screen will turn green.

  8. Turn the knob on the fixture to lower the suction cup as close to the iPhone as possible without touching the iPhone.

    • Caution: To avoid damaging the iPhone, don’t turn the knob before the timer ends.

    • Note: The fixture will beep until the suction cup is lowered.

  9. Grasp the handle and slide the suction cup straight out until the edge of the suction cup aligns close to the bottom edge of the back glass (1).

  10. Turn the knob on the fixture clockwise to lower the suction cup onto the back glass (2). Then flip down the handle on the suction cup to secure the suction cup to the back glass (3).

    • Caution: Don’t let the suction cup hang over the edge of the back glass or you may damage the iPhone. If damaged, stop the repair. You can find a service option at support.apple.com/repair.

    • Important: After the suction cup is lowered onto the iPhone, the screen will begin a 15-minute countdown. When the timer shows 0, the heated display removal fixture will turn off. Ensure that you complete steps 11 and 12 within this time frame.

  11. Slowly turn the knob on the fixture counterclockwise until the back glass begins to separate from the enclosure.

    • Important: If you don’t see a gap between the back glass and the enclosure immediately, wait 30 seconds. If you still don’t see a gap, turn the silver part of the knob counterclockwise until the back glass begins to separate from the enclosure.

    • Caution: Only turn the silver knob if you haven't seen a gap after waiting for 30 seconds.

  12. Insert the edge of the adhesive cutter between the back glass and the enclosure. Run the cutter between the back glass and the enclosure to the right and left as shown until the glass partially releases from the enclosure.

    • Caution: To avoid damaging the flex cables, don’t tilt up the bottom of the display more than 5 degrees.

  13. Flip up the handle to release the suction cup. Then gently slide the flat end of the black stick under the edge of the suction cup to release it from the back glass.

    • Caution: Don’t turn the knob. Turning the knob may damage the flex cables.

  14. Press the eject button on the side of the pocket to release the pocket from the fixture.

  15. Hold both sides of the pocket and slide it straight out of the fixture.

  16. Flip up the clamp on the side of the pocket to release the iPhone (1). Hold the edge of the iPhone and gently remove the iPhone from the pocket (2).

    • Caution: Don’t touch the camera lenses.

  17. Place the iPhone into the repair tray with the camera faceup and the Lightning connector facing the cutout. Remove the gloves.

  18. Slide the back glass slightly toward the bottom of the iPhone.

  19. Insert the edge of the adhesive cutter into the top of the iPhone between the back glass and the enclosure. Hold the adhesive cutter at a 45-degree angle. Start at the middle and cut along the top and sides of the iPhone until the back glass is free.

    • Caution: To avoid damaging the flex cables, don’t tilt the back glass more than 5 degrees.

  20. Insert the repair tray suction cups into the slots in the repair tray.

    • Note: The icon on the bottom of the tray shows the direction to tilt up the back glass and the correct side to place the suction cups.

  21. Tilt up the back glass toward the suction cups. Press the top and bottom edges of the back glass to secure it to the suction cups.

    • Caution: Don’t damage the back glass flex cable as you tilt up the back glass.

    • Warning

      • If the battery is dented, punctured, or otherwise damaged, stop the repair. You can find a service option at support.apple.com/repair.

      • If the back glass is broken, inspect the enclosure. If there are shards of glass in the enclosure, put on the safety glasses with side shields and cut-resistant gloves. Use ESD-safe tweezers to remove the shards. Then use ethanol or IPA wipes to remove any remaining shards from the adhesive on the perimeter of the enclosure. Vacuum any shards of glass from the workspace.

  22. Use a torque driver and the Micro stix bit to remove the trilobe screw from the upper cowling (1) and the two trilobe screws from the lower cowling (2). Set aside the screws.

  23. Use ESD-safe tweezers to remove the lower cowling. Save the cowling for reassembly.

  24. Use ESD-safe tweezers to remove the upper cowling. Save the cowling for reassembly.

  25. Lift the ends of the battery flex cable (1) and the back glass flex cable (2) off the connectors.

    • Caution: You must disconnect the battery flex cable first to ensure that the iPhone stays turned off.

    • Important: Some iPhone 14 Plus models may have a white adhesive shim (1) under the battery flex cable. If you see a white adhesive shim, don’t lift the battery flex cable (2) or touch the white adhesive shim while lifting the end of the flex cable (3) off the connector.

  26. Hold the back glass by the edges. Pull the tabs on the suction cups to release them from the back glass. Then set the back glass facedown on a clean, flat surface.

  27. Remove the suction cups from the repair tray.

  28. Use ESD-safe tweezers to pick up the back glass adhesive. Then pull the adhesive at a 45-degree angle to remove it from the enclosure. Repeat this process until all the adhesive is removed from the perimeter of the enclosure.

    • Caution: Don't touch the camera assembly, TrueDepth camera grounding springs, or nearby parts.

  29. Use ethanol wipes or IPA wipes to clean all residual adhesive from the enclosure.

Reassembly

  1. Place the enclosure in the repair tray with the Lightning connector facing the cutout.

    • Important: If you’re installing a replacement back glass, peel the protective liner from the top and underside of it.

  2. Inspect the TrueDepth camera. Ensure that the top edge of the TrueDepth camera is under the lip of the enclosure.

    • Caution: If the TrueDepth camera is positioned incorrectly, use the black stick to move it into the correct position.

    • Warning: Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

  3. Align the replacement back glass adhesive over the enclosure. Ensure that the top hole of the adhesive aligns over the camera.

    • Caution: Ensure that you’ve removed all residual adhesive from the back glass and the enclosure before you apply the replacement back glass adhesive.

  4. The replacement back glass adhesive has a top release liner, a middle release liner, and a bottom release liner. Grasp the tab on the bottom release liner. Then slowly pull the bottom release liner (1) out from under the adhesive (2) while pressing the adhesive onto the enclosure.

    • Important: Don’t remove the top release liner yet.

      • Bottom release liner (1)

      • Adhesive (2)

    • Note: The replacement back glass adhesive for your model may look different from the illustration, but the steps are the same.

  5. Inspect the back glass adhesive to ensure that it’s positioned on the shelf of the enclosure. If the adhesive isn’t correctly positioned on the enclosure, repeat removal steps 28 and 29. Then repeat reassembly steps 1 through 5.

  6. Place the display adhesive press plate on top of the enclosure with the icon in the top right corner as shown.

    • Important: Ensure that the back glass side of the iPhone is faceup in the repair tray.

  7. Position the repair tray with the iPhone in the display press. Pull down the lever until the display press locks.

  8. Wait until the display press beeps and the timer shows 0. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

    • Caution: To ensure that the back glass adhesive bonds correctly to the enclosure, don’t lift the lever until 30 seconds have passed.

  9. Remove the repair tray from the display press and remove the press plate.

  10. Remove the top release liner in a clockwise direction starting from the middle left side.

    • Important: Don’t remove the remaining release liners adhered around the edge of the enclosure.

      • Top release liner

  11. Insert the suction cups into the repair tray.

  12. Align the right edge of the back glass with the right edge of the enclosure. Gently press along the edges of the back glass to secure it to the suction cups.

    • Important: Don't press the back of the back glass to secure it to the suction cups. Pressing the back may affect functionality.

  13. Press the ends of the back glass and battery flex cables to the connectors.

  14. Position the upper and lower cowlings.

  15. Use the black torque driver and Micro stix bit to install one new trilobe screw (923-02584) (1) into the upper cowling and two new trilobe screws (923-08382) (2) into the lower cowling.

  16. Peel the first strip of the middle release liner (1) counterclockwise, starting at the top right of the enclosure. Peel the second strip (2) clockwise, starting at the top right of the enclosure. Then peel the third strip (3) clockwise, starting at the bottom left of the enclosure.

    • Caution: The second strip of the middle release liner runs under one flex cable. Don't damage the flex cable while removing the release liner.

      • Middle release liner

  17. Inspect the back glass adhesive to ensure that it’s in the correct position and not damaged or wrinkled. If the adhesive is damaged, remove it and apply replacement adhesive.

  18. Repeat step 2 to ensure that the TrueDepth camera is in the correct position. Then continue to step 19.

    • Warning: Inspect the enclosure for loose or extra screws and small parts, which can damage the battery and cause safety issues.

  19. Pull the tabs on the suction cups to release them from the back glass. Tilt down the back glass to rest on the enclosure.

  20. Remove the suction cups from the repair tray.

  21. Press the back glass in the four areas shown simultaneously. Then press along the edges of the back glass until it clicks into place and the back glass is flush with the enclosure.

    • Caution

      • Ensure that the flex cables aren’t trapped between the back glass and the enclosure. Feel the edges of the back glass for variations or gaps. If the back glass isn’t flush, repeat all removal steps and check the flex cables for damage. Then repeat reassembly steps 1 through 21.

      • Don’t touch the camera lenses.

  22. Turn the iPhone over in the repair tray so the display is faceup.

  23. Position the repair tray with the iPhone display faceup in the display press. Pull down the lever until the display press locks.

  24. Wait until the display press beeps and the timer shows 0. Pull down the lever (1) and pull out the release knob (2). Then lift the lever (3).

  25. Remove the repair tray from the display press.

  26. Use the blue torque driver and Torx security bit to install two new security screws, one on each side of the Lightning connector. As you install the screws, press lightly on the display near the Lightning connector. Count five clicks as you install each new screw to ensure that the screw is fully installed.

    • Caution: If the screws aren’t flush, remove and set aside the screws. Then repeat step 26 to install a new set of security screws. If the new screws still aren’t flush, repeat all removal and reassembly steps.

    • Note: Use the correct screw color for your model.

      • Blue, purple, red, starlight, yellow (923-08388)

      • Midnight (923-08387)

Important

Depending on the part replaced, Repair Assistant may be available on the device to finish the repair. Learn how to initiate Repair Assistant.

Note: If you have not run Repair Assistant, the device’s parts and service history may show a part status of “finish repair,” and Apple Diagnostics for Self Service Repair may show a part status of “unknown.”

Published Date: