Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Jump to bottom

试了多个版本（ 905L3B 905L3A 905L3 ） 均不能用U盘启动引导进系统 #1573

Closed
simonchan6688 opened this issue Jul 29, 2023 · 5 comments
Closed

试了多个版本（ 905L3B 905L3A 905L3 ） 均不能用U盘启动引导进系统 #1573

simonchan6688 opened this issue Jul 29, 2023 · 5 comments

Comments

@simonchan6688
Copy link

Device Information | 设备信息

  • SOC: S905L3
  • Model M411A
  • 新魔百和网络机顶盒

Armbian Version | 系统版本

  • Kernel Version: [e.g. 5.15.100]
  • Release: [e.g. jammy/bullseye]

Describe the bug | 问题描述
试了多个版本 605L3B 905L3A 均不能用U盘启动引导进系统。另openwrt也一样。

**机型PCB图
image
image
image

**TTL数据如下：
[ 155.065077@3] SysRq : Emergency Remount R/O
INFO: PSCI Affinity Map:
INFO: AffInst: Level 0, MPID 0x0, State ON
INFO: AffInst: Level 0, MPID 0x1, State ON
INFO: AffInst: Level 0, MPID 0x2, State ON
INFO: AffInst: Level 0, MPID 0x3, State ON
bl31 reboot reason: 0x1
bl31 reboot reason: 0x1
ERROR: gxbb System Reset: SCP error 1.
GXLX2:BL1:3cfee7:42a5ae;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 42533

BL2 Built : 13:36:55, Jun 22 2020.
gxl g85d6ad1 - longyong.chen@droid02-sz

Board ID = 6, adc=458
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz

DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz - FAIL
DDR3 chl: Rank0 16bit @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 912MHz - FAIL
DDR4 chl: Rank0 @ 912MHz
bist_test rank: 0 21 05 3d 37 1f 50 1b 00 37 38 1f 52 18 00 31 3a 23 51 1a 00 34 38 20 51 595 - PASS

Rank0: 2048MB(auto)-2T-18
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00047200
NOTICE: BL3-1: v1.0(debug):361f8a7
NOTICE: BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE: BL31: GXL normal boot!
NOTICE: BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23 yao.zhang@droid07]
efuse init ops = c5
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 f1 b3 50 a0 0 c5 not ES chip
[0.896006 Inits done]
INFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9

U-Boot 2015.01-ge9754dd-dirty (Sep 08 2021 - 17:28:43)

DRAM: 2 GiB
Relocation Offset is: 76eef000
gpio: pin GPIODV_25 (gpio 44) value is 1
register usb cfg[0][1] = 0000000077f617d0
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000073edfac0
aml_priv->desc_buf = 0x0000000073ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
dtb magic 08088b1f
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 10 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 2g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxl plat: p215 vari: 1g
dtb 2 soc: gxlx plat: p261 vari: 1g
dtb 3 soc: gxlx plat: p261 vari: 2g
dtb 4 soc: gxlx plat: p265 vari: 1g
dtb 5 soc: gxlx plat: p265 vari: 2g
dtb 6 soc: gxlx2 plat: p291 vari: 1g
dtb 7 soc: gxlx2 plat: p291 vari: 2g
dtb 8 soc: gxlx2 plat: p295 vari: 1g
dtb 9 soc: gxlx2 plat: p295 vari: 2g
Find match dtb: 7
start dts,buffer=0000000073ee4610,dt_addr=0000000073ee4610
Amlogic multi-dtb tool
Single dtb detected
parts: 16
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: instaboot 0000000020000000 1
07: boot 0000000002000000 1
08: system 0000000040000000 1
09: cache 0000000020000000 2
10: params 0000000004000000 2
11: ctc 0000000012c00000 2
12: bootfiles 0000000020000000 2
13: private 0000000000800000 2
14: flashdata 0000000004000000 2
15: data ffffffffffffffff 4
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 6
hpd_state=1
[720p60hz] is invalid for cvbs.
set hdmitx VIC = 4
config HPLL = 2970
HPLL: 0xc000027b
config HPLL done
j = 2 vid_clk_div = 1
hdmitx: set enc for VIC: 4
HDMITX-DWC addr=0x10004006 rd_data=0x40
Error: HDMITX-DWC exp_data=0xff mask=0x9f
hdmitx phy setting done
div40 = 0
hdmtix: set audio
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-924: calc a44a1108, store a44a1108
_verify_dtb_checksum()-924: calc a44a1108, store a44a1108
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
Amlogic multi-dtb tool
GZIP format, decompress...
Multi dtb detected
2layers board, board id use 7
Multi dtb tool version: v2 .
Support 10 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 2g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxl plat: p215 vari: 1g
dtb 2 soc: gxlx plat: p261 vari: 1g
dtb 3 soc: gxlx plat: p261 vari: 2g
dtb 4 soc: gxlx plat: p265 vari: 1g
dtb 5 soc: gxlx plat: p265 vari: 2g
dtb 6 soc: gxlx2 plat: p291 vari: 1g
dtb 7 soc: gxlx2 plat: p291 vari: 2g
dtb 8 soc: gxlx2 plat: p295 vari: 1g
dtb 9 soc: gxlx2 plat: p295 vari: 2g
Find match dtb: 7
wipe_data=successful
wipe_cache=successful
bmp pixel: 24
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[CANVAS]addr=0x3dc00000 width=5760, height=2160
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[hw] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[model] not programed yet
key1 = 7d82dd22
key2 = 7e81dd22
key3 = 728ddd22
time_out = 7a120
ir init
P_AO_IR_DEC_REG0:70fa0013, P_AO_IR_DEC_REG1:3e70
time_base = 1aca70
out----irkey - irkey key_value1 key_value2 key_value3 time_value

Usage:
irkey
rebootmode=normal
Hit any key to stop autoboot: 0
ee_gate_off ...

Booting Android Image at 0x01080000 ...

reloc_addr =73f648b0
copy done
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
Uncompressing Kernel Image ... OK
kernel loaded at 0x01080000, end = 0x020a1248
Loading Ramdisk to 73e02000, end 73edd4cd ... OK
Loading Device Tree to 000000000fff3000, end 000000000ffffe75 ... OK
signature:
fdt_instaboot: get header err

Starting kernel ...

uboot time: 2909480 us
[ 0.000000@0] Initializing cgroup subsys cpu
[ 0.000000@0] Initializing cgroup subsys cpuacct
[ 0.000000@0] Linux version 3.14.29-g23ac4e1-dirty (proj-gdY-GDYD_znxt_121489@join-r730-00) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #2 SMP PREEMPT Wed Sep 8 17:22:28 CST 2021
[ 0.000000@0] CPU: ARMv71 Processor [410fd034] revision 4
[ 0.000000@0] bootconsole [earlycon0] enabled
get_dvfs_info 0007
INFO: HDCP22 key read fail!
INFO: p1d 0
INFO: pd1 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
WARNING: Unimplemented Sip Call: 0x82000036
root@p201_iptv:/ #
@ophub
Copy link
Owner

ophub commented Jul 29, 2023

先刷第三方高版本安卓系统

@simonchan6688
Copy link
Author

simonchan6688 commented Jul 31, 2023 •
edited
Loading

刷了安卓9 一样无法U盘启动。请问要用哪个包，需要怎样的设置？或者请大佬增加这个机器的支持。谢谢
修正：通过TTL信息可以看到已启动。但是黑屏。使用的是m302a的包

@janko888
Copy link
Contributor

janko888 commented Aug 8, 2023

刷了安卓9 一样无法U盘启动。请问要用哪个包，需要怎样的设置？或者请大佬增加这个机器的支持。谢谢 修正：通过TTL信息可以看到已启动。但是黑屏。使用的是m302a的包

你日志里显示貌似还是在BL阶段，
1，不知道你是否首次正确从adb reboot update或者从TTL console里面reboot update等方式引导进U盘了；
2，引导U盘插入的usb端口一般是靠近网卡那个;
3, U盘本身的兼容性差异也是可能的，多换几种不同的u盘（我手头上不同的读卡器至少5、6款，有时不同的soc有不同的偏向）。此外，最好是usb2.0的。armbian 的usb3.0的驱动貌似不成熟\覆盖不完全？，容易在内核加载时出点小错导致启动失败

@sd7890
Copy link

sd7890 commented Aug 12, 2023

[s905l3]性价比神机mgv3000全网首拆

写完U盘后，打开资源管理器，进入BOOT分区
打开目录下的uEnv.txt，将FDT=/dtb/amlogic/meson-g12a-s905l3a-e900v22c.dtb
改为FDT=/dtb/amlogic/meson-gxl-s905l2-x7-5g.dtb
（S905L2与S905L3理论上最亲。注意S905L3（gxl）与S905L3A（g12a）完全不同，不能混用！）

在根目录找到u-boot-p212.bin重命名为u-boot.ext

这下可以正常地启动u盘的armbian了！

@ophub
Copy link
Owner

ophub commented Aug 12, 2023

楼上sd7890分享的修改结果，是s905l3的默认设置（序号117），你可以下载这个版本的镜像试试。

@ophub ophub closed this as completed Aug 17, 2023
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Assignees
No one assigned
Labels
None yet
Projects
None yet
Milestone
No milestone
Development

No branches or pull requests
4 participants
@simonchan6688 @sd7890 @ophub @janko888