qualcommax: ipq807x: add support for Linksys HomeWRK #17463
Merged
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
github-actions
bot
added
kernel
|
Is there any difference between installing a ubi factory image via
|
|
If its UBI image you should use ubiformat as it will scan for bad blocks first as well as reset the counter to 0 |
robimarko
reviewed
Jan 10, 2025
robimarko
reviewed
Jan 10, 2025
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-homewrk.dts
Outdated
Show resolved
Hide resolved
testuser7
force-pushed
the
homewrk
branch
2 times, most recently
from
25e5d56 to
9ff609c
Compare
|
Can you just bump ipq-wifi since I merged the BDF and I think this is ready to go |
Done. |
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
|
Thanks! Rebased on top of main and merged! |
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 16, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 16, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 16, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 16, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
Vladdrako
pushed a commit
to Vladdrako/openwrt
that referenced
this pull request
Jan 18, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
Vladdrako
pushed a commit
to Vladdrako/openwrt
that referenced
this pull request
Jan 18, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
kimocoder
pushed a commit
to kimocoder/openwrt
that referenced
this pull request
Jan 20, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
kimocoder
pushed a commit
to kimocoder/openwrt
that referenced
this pull request
Jan 20, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 21, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 21, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 22, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 22, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 23, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Jan 23, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
KGeri201
pushed a commit
to KGeri201/openwrt
that referenced
this pull request
Jan 24, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
KGeri201
pushed a commit
to KGeri201/openwrt
that referenced
this pull request
Jan 24, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Feb 1, 2025
Hardware specification: ======== SoC: Qualcomm IPQ8174 Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2) RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L) Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075) WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band) WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11) WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band) LED: 1x RGB status (NXP PCA9633) USB: 1x USB 3.0 Button: WPS, Reset Flash instructions: ======== 1. Installation from initramfs image using USB drive: Put the initramfs image on the USB drive: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Connect serial console (JST PH 6-pin connector): - 1 - GND, 2 - TX, 4 - RX (115200, 8N1, 3.3V) Stop u-boot and run: - usb start && usbboot 44000000 0 && bootm 44000000 Write firmware to the flash from initramfs: - sysupgrade -n openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-sysupgrade.bin or - ubiformat /dev/mtd22 -y -f openwrt-qualcommax-ipq807x-linksys_homewrk-squashfs-factory.ubi 2. USB recovery: Put the initramfs image on the USB: - dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_homewrk-initramfs-uImage.itb of=/dev/sdX Set u-boot env: - fw_setenv bootusb 'usb start && usbboot 44000000 0 && bootm 44000000' - fw_setenv bootcmd 'run bootusb; bootipq' Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
rkboni
pushed a commit
to rkboni/openwrt
that referenced
this pull request
Feb 1, 2025
Envtools can automatically detect the number of blocks. Signed-off-by: Paweł Owoc <frut3k7@gmail.com> Link: openwrt#17463 Signed-off-by: Robert Marko <robimarko@gmail.com>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Hardware specification:
SoC: Qualcomm IPQ8174
Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2)
RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band)
WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11)
WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
Connect serial console (JST PH 6-pin connector):
Stop u-boot and run:
Write firmware to the flash from initramfs:
or
USB recovery:
Put the initramfs image on the USB:
Set u-boot env: