A simple Starlink exporter for Prometheus. Not affiliated with Starlink or SpaceX.
The following metrics are exposed by this exporter:
| Metric name | Description |
|---|---|
starlink_dish_boresight_azimuth_deg |
Starlink dish boresight azimuth degrees |
starlink_dish_boresight_elevation_deg |
Starlink dish boresight elevation degrees |
starlink_dish_currently_obstructed |
Whether the Starlink dish is currently obstructed |
starlink_dish_desired_boresight_azimuth_deg |
Starlink dish desired boresight azimuth degrees |
starlink_dish_desired_boresight_elevation_deg |
Starlink dish desired boresight elevation degrees |
starlink_dish_downlink_throughput_bps_histogram |
Histogram of Starlink dish downlink throughput over last 15 minutes |
starlink_dish_downlink_throughput_bps |
Starlink dish downlink throughput in bit/sec |
starlink_dish_fraction_obstruction_ratio |
Fraction of Starlink dish that is obstructed |
starlink_dish_gps_satellites |
Number of GPS satellites visible to the Starlink dish |
starlink_dish_gps_valid |
Whether the Starlink dish GPS is valid |
starlink_dish_info |
Starlink dish software information |
starlink_dish_last_24h_obstructed_seconds |
Number of seconds the Starlink dish was obstructed in the past 24 hours |
starlink_dish_pop_ping_drop_ratio |
Starlink PoP ping drop ratio |
starlink_dish_pop_ping_latency_seconds_histogram |
Histogram of Starlink dish PoP ping latency in seconds over last 15 minutes |
starlink_dish_pop_ping_latency_seconds |
Starlink PoP ping latency in seconds |
starlink_dish_power_input_watts_histogram |
Histogram of Starlink dish power input in watts over last 15 minutes |
starlink_dish_power_input_watts |
Current power input for the Starlink dish |
starlink_dish_snr_above_noise_floor |
Whether Starlink dish signal-to-noise ratio is above noise floor |
starlink_dish_snr_persistently_low |
Whether Starlink dish signal-to-noise ratio is persistently low |
starlink_dish_software_update_reboot_ready |
Whether the Starlink dish is ready to reboot to apply a software update |
starlink_dish_tilt_angle_deg |
Starlink dish tilt angle degrees |
starlink_dish_up |
Whether scraping metrics from the Starlink dish was successful |
starlink_dish_uplink_throughput_bps_histogram |
Histogram of Starlink dish uplink throughput in bits/sec over last 15 minutes |
starlink_dish_uplink_throughput_bps |
Starlink dish uplink throughput in bits/sec |
starlink_dish_uptime_seconds |
Starlink dish uptime in seconds |
starlink_exporter_scrape_duration_seconds |
Time taken to scrape metrics from the Starlink dish |
starlink_exporter_scrapes_total |
Total number of Starlink dish scrapes |
Pre-built binaries are available from GitHub Releases.
You can also use go install to build and install a binary from source:
go install github.com/joshuasing/starlink_exporter@latestFlags
starlink_exporter --help
# Usage of starlink_exporter:
# -dish string
# Dish address (default "192.168.100.1:9200")
# -listen string
# Listen address (default ":9451")Example
starlink_exporter
# 2024/11/05 12:03:48 INFO Starting Starlink exporter
# 2024/11/05 12:03:48 INFO Connecting to Starlink Dishy address=192.168.100.1:9200
# 2024/11/05 12:03:48 INFO HTTP server listening address=:9451Docker images are published to both GitHub Container Registry (ghcr.io) and Docker Hub.
docker run -p 9451:9451 ghcr.io/joshuasing/starlink_exporter:latest
# Status: Downloaded newer image for ghcr.io/joshuasing/starlink_exporter:latest
# 2024/11/05 12:03:48 INFO Starting Starlink exporter
# 2024/11/05 12:03:48 INFO Connecting to Starlink Dishy address=192.168.100.1:9200
# 2024/11/05 12:03:48 INFO HTTP server listening address=:9451To use the Starlink Prometheus Exporter, you need to configure Prometheus to scrape from the exporter:
scrape_configs:
- job_name: "starlink"
scrape_interval: 3s # This can be whatever you would like.
static_configs:
- targets: [ "localhost:9451" ]Change scrape_interval and the address to match your setup.
All contributions are welcome! If you have found something you think could be improved, or have discovered additional metrics you would like included, please feel free to participate by creating an issue or pull request!
Steps to build starlink_exporter.
Prerequisites
- Go v1.23 or newer (https://go.dev/dl/)
Build
- Make:
make(make deps lint-depsif you are missing dependencies) - Standalone:
go build ./cmd/starlink_exporter/
This project is maintained by Joshua Sing. You see a list of ways to contact me on my website: https://joshuasing.dev/#contact
I take the security of my projects very seriously. As such, I strongly encourage responsible disclosure of security vulnerabilities.
If you have discovered a security vulnerability in starlink_exporter, please report it in accordance with the project Security Policy. Never use GitHub issues to report a security vulnerability.
starlink_exporter is distributed under the terms of the MIT License.
For more information, please refer to the LICENSE file.
This project is an independent, open-source Prometheus exporter and is not officially associated with, endorsed by, or in any way affiliated with SpaceX, Starlink, or any of their subsidiaries or affiliates. This project's purpose is to provide a tool for easily monitoring your Starlink Dishy with Prometheus, and is not authorised or supported by SpaceX or Starlink in any way.
SpaceX, Starlink, and any related logos or trademarks are the property of Space Exploration Technologies Corp.
