Basic support for JM60 keyboard

This adds basic support for JM60 RGB PCB that was sold by KBDfans https://kbdfans.myshopify.com/ https://www.aliexpress.com/store/product/JM60-RGB60-Custom-mechanical-keyboard-PCB-ANSI/2230037_32810956675.html No support for RGB Backlight yet.
jcf · Sep 11, 2017 · 349e001 · 349e001
1 parent 68b6de6
commit 349e001
Show file tree

Hide file tree

Showing 17 changed files with 1,903 additions and 0 deletions.
diff --git a/keyboards/jm60/Makefile b/keyboards/jm60/Makefile
@@ -0,0 +1,3 @@
+ifndef MAKEFILE_INCLUDED
+	include ../../Makefile
+endif
diff --git a/keyboards/jm60/boards/JM60_BOARD/board.c b/keyboards/jm60/boards/JM60_BOARD/board.c
@@ -0,0 +1,51 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#include "hal.h"
+
+/**
+ * @brief   PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ *          This variable is used by the HAL when initializing the PAL driver.
+ */
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+const PALConfig pal_default_config =
+{
+  {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
+  {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
+  {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
+  {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
+  {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
+};
+#endif
+
+/*
+ * Early initialization code.
+ * This initialization must be performed just after stack setup and before
+ * any other initialization.
+ */
+void __early_init(void) {
+
+  stm32_clock_init();
+}
+
+/*
+ * Board-specific initialization code.
+ */
+void boardInit(void) {
+	AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE;
+
+}
diff --git a/keyboards/jm60/boards/JM60_BOARD/board.h b/keyboards/jm60/boards/JM60_BOARD/board.h
@@ -0,0 +1,142 @@
+/*
+    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Board identifier.
+ */
+#define BOARD_JM60
+#define BOARD_NAME              "JM60 keyboard"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK            32768
+#define STM32_HSECLK            8000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ *
+ * Only xB (128KB Flash) is defined, but it's identical to the
+ * x8 version (64KB Flash) except for the Flash region size in the
+ * linker script. For x8 parts use xB here and change to the x8 linker
+ * script in the project Makefile.
+ */
+#define STM32F103xB
+
+/*
+ * IO pins assignments
+ *
+ * numbering is sorted by onboard/connectors, as from the schematics in
+ * http://www.vcc-gnd.com/read.php?tid=369
+ */
+
+/* on-board */
+#define GPIOA_USBDM             11      // pin 8
+#define GPIOA_USBDP             12      // pin 9
+
+#define GPIOC_OSC32_IN          14
+#define GPIOC_OSC32_OUT         15
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ *   0 - Analog input.
+ *   1 - Push Pull output 10MHz.
+ *   2 - Push Pull output 2MHz.
+ *   3 - Push Pull output 50MHz.
+ *   4 - Digital input.
+ *   5 - Open Drain output 10MHz.
+ *   6 - Open Drain output 2MHz.
+ *   7 - Open Drain output 50MHz.
+ *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ *   9 - Alternate Push Pull output 10MHz.
+ *   A - Alternate Push Pull output 2MHz.
+ *   B - Alternate Push Pull output 50MHz.
+ *   C - Reserved.
+ *   D - Alternate Open Drain output 10MHz.
+ *   E - Alternate Open Drain output 2MHz.
+ *   F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOACRL            0x88888888      /*  PA7...PA0 */
+#define VAL_GPIOACRH            0x88888888      /* PA15...PA8 */
+#define VAL_GPIOAODR            0xFFFFFFFF
+
+/*
+ * Port B setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */
+#define VAL_GPIOBCRH            0x88888888      /* PB15...PB8 */
+#define VAL_GPIOBODR            0xFFFFFFFF
+
+/*
+ * Port C setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */
+#define VAL_GPIOCCRH            0x88888888      /* PC15...PC8 */
+#define VAL_GPIOCODR            0xFFFFFFFF
+
+/*
+ * Port D setup.
+ * Everything input with pull-up except:
+ * PD0  - Normal input (XTAL).
+ * PD1  - Normal input (XTAL).
+ */
+#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
+#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
+#define VAL_GPIODODR            0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
+#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
+#define VAL_GPIOEODR            0xFFFFFFFF
+
+/*
+ * USB bus activation macro, required by the USB driver.
+ */
+#define usb_lld_connect_bus(usbp)	/* always connected */
+
+/*
+ * USB bus de-activation macro, required by the USB driver.
+ */
+#define usb_lld_disconnect_bus(usbp)	/* always connected */
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+  void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
diff --git a/keyboards/jm60/boards/JM60_BOARD/board.mk b/keyboards/jm60/boards/JM60_BOARD/board.mk
@@ -0,0 +1,5 @@
+# List of all the board related files.
+BOARDSRC = $(KEYBOARD_PATH)/boards/JM60_BOARD/board.c
+
+# Required include directories
+BOARDINC = $(KEYBOARD_PATH)/boards/JM60_BOARD