Uno/Nano compatible code that will drive a shift light. Credits to Chippernut for the original version I based this off.
- Download and install each of the dependencies.
- Double check the
_defines.hfile corresponds to your wiring. - Compile and upload using Arduino IDE 1.6.5+
' = Custom version, take from my repos or a fork of them. Should my changes get merged upstream I will modify this list.
| Displayed | Means | Range | Description |
|---|---|---|---|
Pr 1 |
Profile 1 | See below | Edit or selects profile 1. Works the same for other profile numbers. |
Pr-- |
Create Profile | - | Creates a new profile (max 5). |
Lo |
Low RPM | StAt-Acti |
The maximum RPM value that is considered low RPM, shift down when passing this value. |
Acti |
Activation RPM | 1000-ShFt |
The RPM value at which the first pixel will light up. |
ShFt |
Shift RPM | Acti-9900 |
The RPM value after which the pixels will start flashing. |
Ani |
Animation | See below | The animation style displayed. |
ltr |
Left-to-Right | - | Animation style that will fill pixels from the left. |
rtl |
Right-to-Left | - | Animation style that will fill pixels from the right. |
Out |
Outward | - | Animation style that will fill from the center out. |
In |
Inward | - | Animation style that will fill from the edges inward. |
FULL |
Full bar | - | Animation style that uses color and flashing only, alwasys a filled bar. (Experimental) |
CLrS |
Colors | See below | Allows you to enter a sub-menu for editing the pixel colors. |
C Lo |
Color Low RPM | Color | The color to use for Low RPM indicator. |
CPt1 |
Color Part 1 | Color | The first color for the chosen animation style, when between Acti and ShFt. |
CPt2 |
Color Part 2 | Color | The second color for the chosen animation style, when between Acti and ShFt. |
CPt3 |
Color Part 3 | Color | The third color for the chosen animation style, when between Acti and ShFt. |
CFL1 |
Color Flash 1 | Color | The first color used for shift flashing, after ShFt value. |
CFL2 |
Color Flash 2 | Color + Black | The second color used for shift flashing, after ShFt value. |
del |
Delete profile | - | Deletes the profile you're currently editing. |
Lcd |
LCD Brightness | 1-8 | The brightness value for the 7-seg LCD display. |
CSeg |
Color Segments | - | Allows you to set the different segment sizes (full and halved length). |
ti |
Time | See below | Allows you to set the date and time. |
20## |
Year | 2000-2099 | Sets the current year. |
n ## |
Nonth | 1-12 | Sets the current nonth (n is used because m can't be displayed on the 7-seg display). |
d ## |
Date | 1-31 | Sets the current date. |
##:00 |
Hour | 0-23 | Sets the current hour. |
00:## |
Minute | 0-59 | Sets the current minute. |
SteP |
RPM Steps | 1, 2, 5, 10, 20, 50, 100 | Rounds the RPM value displayed on the LCD. (Does not affect calculations/animations.) |
StAt |
Stationary RPM | 1000-Acti |
The RPM value which is considered less than low RPM. Low RPM blinking will stop when below this value. |
PPr |
Pulses Per Revolution | 1-12 | The amount of pulses your vehicle's ECU sends per revolution. Depends mainly on the amount of cylincers. |
BuFF |
Buffer | yes/no | Whether or not to use a buffer to smooth out RPM readings. |
tyPe |
RPM Measurement Type | 1-2 | The type of measurement to do to get the RPM signal. 1 = Interrupt based, 2 = Timer1 based. |
rSet |
Reset | See below | Will reset all configuration to default values. |
Sure |
Are you sure? | - | Confirmation that you want to reset to default values. |
Created with KiCad, originals in docs folder.