Troubleshooting Tip: Video Filter Debugging Comman...

Renante_Era · 01-08-2025

Description This article describes how to list the FortiGate local users. Scope FortiGate Solution FortiGate local users are in config user local. Using the commands show user local will display unnecessary fields. To display a concise list of users,...

Renante_Era · 01-02-2025

Description This article describes the setup when configuring the communication between a Local Area Network (LAN) and a Wireless LAN. Scope FortiGate, FortiAP. Solution When configuring the SSID for FortiAP, two of the most common traffic mode optio...

Renante_Era · 12-17-2024

Description This article describes the generic configuration steps when the internet traffic of a third-party router needs to egress to FortiGate which is located across the IPsec tunnel VPN. Scope FortiGate. Solution Third-party routers might not ha...

Renante_Era · 12-12-2024

Description This article describes how to check whether the FortiGate config and SIP ALG were already disabled or not. Scope FortiGate. Solution The following are the steps that can be followed when unsure if SIP ALG is disabled or not. Open the Fort...

Renante_Era · 12-10-2024

Description This article describes how to trousbleshoot when an endpoint is unable to telnet to a public server. Scope FortiGate. Solution An endpoint might not be able to connect to a public server due to the specific routing configuration of the Fo...

Renante_Era · 01-07-2025

You can manage each FortiGate via CLI using # exec ha manage . For instance, # exec ha manage 1 admin <-- use 0 if 1 didn't work Alternatively, you can manage each device separately through the GUI: Out-of-band management with reserved management in...

Renante_Era · 01-07-2025

Review the config of your Edgmax router and see if there's a port forwarding entry to open the PBX from WAN>LAN. If that's the case, then you'll need to configure Virtual IPs on the FortiGate. Configuring a virtual IP | FortiPortal 7.2.0 | Fortinet D...

Renante_Era · 12-30-2024

You'll need Virtual IP for that to work as shown in the following KB: Site-to-site VPN with overlapping subnets | FortiGate / FortiOS 7.4.3 | Fortinet Document Library

Renante_Era · 12-27-2024

If you're unable to access the FortiGate, then your next step is to factory reset the device which means you're going to lose the config. If you have a backup config, then you can restore the backup config on the same firmware version. If you don't h...

Renante_Era · 12-27-2024

since it's only one host, why not assign static IP address on that device instead of obtaining IP address from DHCP?

User Statistics

User Activity

Technical Tip: List FortiGate Local Users

Technical Tip: Communication between LAN and Wireless LAN

Technical Tip: Configure third-party router to egress internet traffic to FortiGate across IPsec tunnel

Troubleshooting Tip: How to check FortiGate config if SIP ALG is disabled

Troubleshooting Tip: Initial troubleshooting steps when endpoint is unable to telnet to a public server

Re: Managing a FortiGate HA Cluster (Active-Active) Without FortiManager

Re: Truncal sip appears unreachable behind the Fortinet 60f using Issabel Pbx

Re: Policy Question - NAT IP Pool

Re: Problem with Fortinet 100E

Re: DHCP option problem

Troubleshooting Tip: Video Filter Debugging Comman...

Troubleshooting Tip: ZTNA tagging issue debugging ...

Re: Managing a FortiGate HA Cluster (Active-Active...

Re: SSL-VPN, exclude specific login address

Re: Clarification on upgrades with manipulate part...

Re: Request for help getting started with global A...

KCS

User Statistics

User Activity

You are leaving our website