Arduino SONY S-LINK/Control-A1 Protocol Library.

This library allows to drive Sony audio consumer devices connected through the Sony S-Link bus-system.

It also includes trivial monitoring capabilities for the S-Link interface, to test and dump received sequences.

(C) Ircama, 2017, CC-BY-SA 4.0 https://creativecommons.org/licenses/by-sa/4.0/

In standard operation, the code is targeted to the ATtiny85 microcontroller (e.g. Digispark ATtiny85). As the ATtiny85 USB interface does not allow confortable monitoring and debugging features, dumping the S-Link interface can be achieved through an ATmega328P micro (e.g., Arduino Nano).

Examples of sketches using this library:

• https://github.com/Ircama/AtTinyTestIR
• https://github.com/Ircama/IR2SLink

For Digispark ATTINY85 check also this note: https://gist.github.com/Ircama/22707e938e9c8f169d9fe187797a2a2c

Create a new folder called "Sony_SLink" under the folder named "libraries" in your Arduino sketchbook folder. Create the folder "libraries" in case it does not exist yet. Place all the files in the "Sony_SLink" folder.

To use the library in your own sketch, select it from Sketch > Import Library.

Simplest example of using this library:

#define SLINK_PIN 2 // S-Link Control-A1 pin

#include "Sony_SLink.h"
Slink slink;

void setup() {
  slink.init(SLINK_PIN); // Set-up S-Link pin
  slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_POWER_ON);
}

void loop() {
}

Check the examples directory for further examples.

slink.init(slinkPin) - set-up S-Link pin

slink.sendCommand(device, command) - send a command to the device; check Sony_SLink.h for available commands

Examples:

slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_VOLUME_UP);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_VOLUME_DOWN);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_POWER_OFF);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_POWER_OFF);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_POWER_ON);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_SET_INPUT_CHAN, SLINK_CMDP_IN_TV);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_MUTE_ON);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_MUTE_OFF);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_SET_INPUT_CHAN, SLINK_CMDP_IN_TUNER);
slink.sendCommand(SLINK_DEVICE_AMP, SLINK_CMD_AMP_SET_INPUT_CHAN, SLINK_CMDP_IN_CD);
slink.sendCommand(SLINK_DEVICE_TUNER, SLINK_CMD_TUNER_PRESET_UP);
slink.sendCommand(SLINK_DEVICE_TUNER, SLINK_CMD_TUNER_PRESET_DOWN);
slink.sendCommand(SLINK_DEVICE_TUNER, SLINK_CMD_TUNER_PRESET_STATION, 1, 1);

slink.inputMonitor - monitor SLink input Available options:

slink.inputMonitor(0); // measure timing of mark periods in microseconds (sync should be 2400, one about 1200, zero ab. 600)
slink.inputMonitor(1); // monitor bytes displaying binary and HEX format of each byte
slink.inputMonitor(2); // monitor bytes displaying HEX dump
slink.inputMonitor(0, true); // measure timing of idle periods (e.g., delimiter; all idle periods should be about 600 microseconds)

The STR-DA1000ES receiver (3V TTL, 112 AMP device ID) needs some amount of wait time between the volume up and down codes (20 and 21) to actually change the volume. From some experimentation, timing seems to be between 3ms and 1960ms. Any shorter or longer and the volume won't change.

Example:

void loop() {
slink.sendCommand(112, 20);
delay(3); //up to delay(1960);
}

Code heavily based on:

• hajdbo's code: https://github.com/hajdbo/sony-jukebox-slink/blob/master/jukebox.pde
• EdsterG's code: https://github.com/EdsterG/LANC_Library

Reference documents:

• Sony S-Link gateway document: http://ee.bradley.edu/projects/proj2001/sonyntwk/SLink.PDF

• How SONY's S-LINK/CTRL-A(II) protocol works (waveform): http://boehmel.de/slink.htm

• Codes for Sony STR-DA50ES receiver: http://www.hifi-remote.com/sony/Sony_dsp_192.htm

• S-Link Parallel Device for Linux http://web.archive.org/web/20040722060841/http://www.undeadscientist.com/slink/index.html

• Reverse Engineered Control-A1 codes (Using the Sony CDP-CX250) Written by BigDave (2/19/98) http://web.archive.org/web/19981202175957/http://www.cc.gatech.edu/people/home/bigdave/cdplayer/control-a1.txt

• Working S-Link code - Background of the S-link protocol http://forums.parallax.com/discussion/70973/working-s-link-code-long

• Slink Send and Receive Commands for Sony MiniDisc Recorders http://web.archive.org/web/20030419100153/http://web2.airmail.net/will/mdslink.txt

• Jukebox Interface Guide http://web.archive.org/web/20030414200645/http://www.upl.cs.wisc.edu/~orn/jukebox/guide.html

• Original Control-A1 document http://web.archive.org/web/20030414231523/http://www.upl.cs.wisc.edu/~orn/jukebox/controla1.html

Tested with a Sony STR-DA50ES receiver/amplifier. Service manual: http://sportsbil.com/sony/STR/STR-D/STR-DA30ES_DA50ES_V55ES_v1.1.pdf

This protocol is very slow: average 355 bps half duplex for a standard two-byte send transmission taking 45 millisecs (355=16/0,045).

Feel free to share this source code, but include explicit mention to the author. Licensed under creative commons - see http://creativecommons.org/licenses/by-sa/4.0/